NF EN ISO 1101

NF EN ISO 1101

May 2013
Standard Cancelled

Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out

ISO 1101:2012 contains basic information and gives requirements for the geometrical tolerancing of workpieces. It represents the initial basis and defines the fundamentals for geometrical tolerancing.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

May 2013

Number of pages

116 p.

Reference

NF EN ISO 1101

ICS Codes

01.100.20   Mechanical engineering drawings
17.040.10   Limits and fits
17.040.40   Geometrical Product Specification (GPS)

Classification index

E04-552

Print number

1 - 30/04/2013

International kinship

ISO 1101:2012

European kinship

EN ISO 1101:2013
Sumary
Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out

ISO 1101:2012 contains basic information and gives requirements for the geometrical tolerancing of workpieces. It represents the initial basis and defines the fundamentals for geometrical tolerancing.

Replaced standards (3)
NF EN ISO 1101
January 2006
Standard Cancelled
Geometrical Product Specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out

<p>ISO 1101:2004 contains basic information and gives requirements for the geometrical tolerancing of workpieces.</p>

NF ISO 10578
April 1996
Standard Cancelled
Technical drawings. Tolerancing of orientation and location. Projected tolerance zone.

XP E04-562
December 2000
Standard Cancelled
Geometrical product specification (GPS) - Complex, prismatic and revolute surfaces - Specification on drawings

Le présent document détaille la façon d'exprimer les exigences géométriques des surfaces complexes, prismatiques et de révolution en en précisant la signification. La situation du présent document dans la matrice GPS est donnée en annexe E.

Standard replaced by (1)
NF EN ISO 1101
April 2017
Standard Current
Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out

Le présent document constitue la base du tolérancement géométrique. Il fixe les notions fondamentales, principes, définitions, symboles et mode d'indication sur les dessins et spécifie les exigences pour le tolérancement géométrique des pièces. Les tolérances concernées sont les tolérances de forme (rectitude, planéité, circularité, cylindricité, profil d'une ligne, profil d'une surface) , les tolérances d'orientations (parallélisme, perpendicularité, inclinaison, profil d'une ligne, profil d'une surface) , les tolérances de position (localisation) concentricité, coaxialité, symétrie, profil d'une ligne, profil d'une surface) , les tolérances de battement (battement circulaire, battement total) . La situation du présent document dans la matrice GPS est donnée en Annexe G.

Table of contents
View the extract
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    2
  • 4 Concept de base
    4
  • 5 Symboles
    5
  • 6 Cadre de tolérance
    7
  • 7 Éléments tolérancés
    8
  • 8 Zones de tolérances
    10
  • 9 Références spécifiées
    16
  • 10 Indications complémentaires
    19
  • 11 Dimensions théoriques exactes (TED)
    25
  • 12 Spécifications restrictives
    25
  • 13 Zone de tolérance projetée
    27
  • 14 Condition à l'état libre
    30
  • 15 Relation entre tolérances géométriques
    30
  • 16 Plans d'intersection
    31
  • 17 Plans d'orientation
    33
  • 18 Définitions des tolérances géométriques
    36
  • Annexe A (informative) Anciennes pratiques
    93
  • Annexe B (normative) Évaluation des écarts géométriques
    96
  • Annexe C (normative) Relations et dimensions des symboles graphiques
    100
  • Annexe D (informative) Relation avec la matrice GPS
    102
  • Bibliographie
    104
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ