NF EN ISO 1302

NF EN ISO 1302

April 2002
Standard Cancelled

Geometrical Product Specification (GPS) - Indication of surface texture in technical product documentation

This International Standard specifies the rules for the indication of surface texture in technical product documentation (e.g. drawings, specifications, contracts, reports) by means of graphical symbols and textual indications. It is applicable to the indication of requirements for surfaces by means of profile parameters, according to ISO 4287, related to the R-profile (roughness parameters), W-profile (waviness parameters) and P-profile (structural parameters), to motif parameters, according to ISO 12085, related to the roughness motif and waviness motif, as well as to parameters related to the material ratio curve according to ISO 13565-2 and ISO 13565-3. NOTE For the indication of requirements for surface imperfections (pores, scratches etc.), which cannot be specified using surface texture parameters, reference is made to ISO 8785, which covers surface imperfections.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

April 2002

Number of pages

61 p.

Reference

NF EN ISO 1302

ICS Codes

01.100.01   Technical drawings in general
17.040.20   Properties of surfaces
17.040.40   Geometrical Product Specification (GPS)

Classification index

E05-016

Print number

1 - 07/12/2002

International kinship

ISO 1302:2002

European kinship

EN ISO 1302:2002
Sumary
Geometrical Product Specification (GPS) - Indication of surface texture in technical product documentation

This International Standard specifies the rules for the indication of surface texture in technical product documentation (e.g. drawings, specifications, contracts, reports) by means of graphical symbols and textual indications.

It is applicable to the indication of requirements for surfaces by means of profile parameters, according to ISO 4287, related to the R-profile (roughness parameters), W-profile (waviness parameters) and P-profile (structural parameters), to motif parameters, according to ISO 12085, related to the roughness motif and waviness motif, as well as to parameters related to the material ratio curve according to ISO 13565-2 and ISO 13565-3.

NOTE For the indication of requirements for surface imperfections (pores, scratches etc.), which cannot be specified using surface texture parameters, reference is made to ISO 8785, which covers surface imperfections.

Replaced standards (1)
NF ISO 1302
November 1995
Standard Cancelled
Technical drawings. Method of indicating surface texture.

Standard replaced by (1)
NF EN ISO 21920-1
January 2022
Standard Current
Geometrical product specifications (GPS) - Surface texture : profile - Part 1 : indication of surface texture

<p>This document specifies the rules for indication of surface texture by profile methods in technical product documentation by means of graphical symbols.</p> <p>This document does not cover population requirements.</p> <p>NOTE       See ISO 18391 for population (batch) specifications.</p>

Table of contents
View the extract
  • Avant-propos
    IV
  • Introduction
    V
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    3
  • 4 Symboles graphiques pour l'indication de l'état de surface
    3
  • 5 Composition du symbole graphique complet pour état de surface
    5
  • 6 Indication des paramètres d'état de surface
    6
  • 7 Indication de la méthode de fabrication ou information correspondante
    12
  • 8 Indication des stries de surface
    13
  • 9 Indication des surépaisseurs d'usinage
    13
  • 10 Résumé des indications des exigences d'état de surface et de leurs valeurs
    15
  • 11 Position sur les dessins et autre documentation technique de produits
    15
  • Annexe A (normative) Proportions et dimensions des symboles graphiques
    21
  • Annexe B (informative) Tableaux synoptiques
    24
  • Annexe C (informative) Exemples d'indication d'exigences d'état de surface
    27
  • Annexe D (informative) Indications minimales afin d'assurer une maîtrise non ambiguë des fonctions de surface
    32
  • Annexe E (informative) Désignation des paramètres d'état de surface
    35
  • Annexe F (informative) Longueur d'évaluation, ln
    38
  • Annexe G (informative) Bande de transmission et longueur de base
    40
  • Annexe H (informative) Explication approfondie sur les conséquences des nouvelles normes ISO en matière d'état de surface
    42
  • Annexe I (informative) Pratique antérieure
    44
  • Annexe J (informative) Relation avec la matrice GPS
    47
  • Bibliographie
    49
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ