NF EN ISO 14120

NF EN ISO 14120

January 2016
Standard Current

Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards

ISO 14120:2015 specifies general requirements for the design, construction, and selection of guards provided to protect persons from mechanical hazards. ISO 14120:2015 indicates other hazards that can influence the design and construction of guards. ISO 14120:2015 applies to guards for machinery which will be manufactured after it is published. The requirements are applicable if fixed and movable guards are used. This International Standard does not cover interlocking devices. These are covered in ISO 14119. ISO 14120:2015 does not provide requirements for special systems relating specifically to mobility such as ROPS (rollover protective structures), FOPS (falling-object protective structures), and TOPS (tip over protective structures) or to the ability of machinery to lift loads.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Thematics

QSE, Sécurité, Gestion des risques et SST

Publication date

January 2016

Number of pages

45 p.

Reference

NF EN ISO 14120

ICS Codes

13.110   Safety of machinery

Classification index

E09-060

Print number

1

International kinship

ISO 14120:2015

European kinship

EN ISO 14120:2015
Sumary
Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards

ISO 14120:2015 specifies general requirements for the design, construction, and selection of guards provided to protect persons from mechanical hazards.

ISO 14120:2015 indicates other hazards that can influence the design and construction of guards.

ISO 14120:2015 applies to guards for machinery which will be manufactured after it is published.

The requirements are applicable if fixed and movable guards are used. This International Standard does not cover interlocking devices. These are covered in ISO 14119.

ISO 14120:2015 does not provide requirements for special systems relating specifically to mobility such as ROPS (rollover protective structures), FOPS (falling-object protective structures), and TOPS (tip over protective structures) or to the ability of machinery to lift loads.

Replaced standards (1)
NF EN 953+A1
May 2009
Standard Cancelled
Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards

Le présent document fait partie d'une série de normes de sécurité. Il traite des protecteurs et donne des éléments aux concepteurs de machines et aux rédacteurs de normes de sécurité pour les machines particulières, pour assurer une présomption de conformité par rapport aux exigences essentielles relatives aux protecteurs des Directives " Machines " 98/37/CE et 2006/42/CE.

Table of contents
View the extract
  • Avant-propos
  • 1 Domaine d'application
  • 2 Références normatives
  • 3 Termes et définitions
  • 4 Appréciation du risque
  • 5 Prescriptions générales pour la conception et la construction des protecteurs
  • 6 Choix des types de protecteurs
  • 7 Vérification des prescriptions de sécurité relatives aux protecteurs
  • 8 Information pour l'utilisation
  • Annexe A (informative)Exemple de fixation imperdable
  • Annexe B (informative)Exemple de méthode d'essai de projectile pour essais mécaniques de protecteurs
  • Annexe C (informative)Exemple de méthode d'essai au pendule pour essais mécaniques de protecteurs
  • Annexe D (informative)Relation entre les Normes internationales citées dans l'Article 2et les Normes européennes correspondantes
  • Annexe ZA(informative) Relation entre la présente Norme européenne et les exigences essentielles de la Directive 2006/42/CE
  • Bibliographie
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ