NF EN ISO 1452-3
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3 : fittings
ISO 1452-3:2009 specifies the characteristics of fittings made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to. In conjunction with ISO 1452-1, ISO 1452-2 and ISO 1452-5, it is applicable to PVC‑U fittings and to joints with components of PVC‑U, other plastics and non-plastics materials intended to be used for the following: - water mains and services buried in the ground; - conveyance of water above ground for both outside and inside buildings; - buried and above ground drainage and sewerage under pressure. It is applicable to fittings in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.
ISO 1452-3:2009 specifies the characteristics of fittings made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2 and ISO 1452-5, it is applicable to PVC‑U fittings and to joints with components of PVC‑U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to fittings in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.
Le présent document spécifie les aspects généraux des systèmes de canalisations en poly(chlorure de vinyle) non plastifié (PVC-U) dans le domaine de l'assainissement enterré et aérien avec pression.
Le présent document précise les caractéristiques des raccords en poly(chlorure de vinyle) non plastifié (PVC-U). Il est applicable aux systèmes de canalisations pour l'alimentation en eau destinée à la consommation humaine, jusqu'à 45 °C inclus.
<p>ISO 1452-3:2009 specifies the characteristics of fittings made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.</p> <p>In conjunction with ISO 1452-1, ISO 1452-2 and ISO 1452-5, it is applicable to PVC‑U fittings and to joints with components of PVC‑U, other plastics and non-plastics materials intended to be used for the following:</p> <p>- water mains and services buried in the ground;</p> <p>- conveyance of water above ground for both outside and inside buildings;</p> <p>- buried and above ground drainage and sewerage under pressure.</p> <p>It is applicable to fittings in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C. </p>
- Avant-proposiv
- Introductionv
-
1 Domaine d'application1
-
2 Références normatives2
-
3 Termes, définitions, symboles et abréviations3
-
3.1 Termes et définitions3
-
3.2 Symboles3
-
4 Matière3
-
4.1 Matière des raccords3
-
4.2 Masse volumique4
-
4.3 Valeur MRS4
-
5 Caractéristiques générales4
-
5.1 Aspect4
-
5.2 Couleur4
-
5.3 Opacité des raccords pour le transport de l'eau en aérien4
-
6 Caractéristiques géométriques4
-
6.1 Mesurage des dimensions4
-
6.2 Diamètres nominaux4
-
6.3 Raccords à coller5
-
6.4 Raccords d'adaptation13
-
6.5 Selles de branchements15
-
6.6 Collets et brides18
-
6.7 Raccords à bague d'étanchéité en élastomère21
-
6.8 Doubles manchons à bague d'étanchéité supportant l'effet de fond30
-
7 Classification et conditions de service30
-
7.1 Classification30
-
7.2 Sélection de la pression nominale PN et les séries de tube S pour de l'eau jusqu'à 25 °C inclus31
-
7.3 Détermination de la pression de service admissible PFA pour l'eau jusqu'à 45 °C31
-
8 Caractéristiques mécaniques31
-
8.1 Résistance à la pression interne des raccords ou composants de raccords31
-
8.2 Essai d'écrasement32
-
9 Caractéristiques physiques32
-
10 Bagues d'étanchéité33
-
11 Adhésifs33
-
12 Exigences de performance34
-
13 Marquage34
-
13.1 Généralités34
-
13.2 Marquage minimal exigé34
-
13.3 Marquage supplémentaire35
- Annexe A (normative) Raccords en dimensions impériales (en pouces)36
- Bibliographie39
The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.
The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.
With Requirements, quickly access the main part of the normative text!
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ