NF EN ISO 15011-2

NF EN ISO 15011-2

November 2009
Standard Current

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 2 : determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging

ISO 15011-2:2009 defines laboratory methods for measuring the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) generated during arc welding, cutting and gouging, using a hood technique. The methodology is suitable for use with all open arc welding processes, cutting and gouging, but different designs of hood are used depending on the process and whether or not it can be conducted automatically.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Thematics

Gestion des risques et SST, QSE, Sécurité

Publication date

November 2009

Number of pages

27 p.

Reference

NF EN ISO 15011-2

ICS Codes

13.040.30   Workplace atmospheres
13.100   Occupational safety. Industrial hygiene
25.160.10   Welding processes

Classification index

A88-200-2

Print number

1 - 27/11/2009

International kinship

ISO 15011-2:2009

European kinship

EN ISO 15011-2:2009
Sumary
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 2 : determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging

ISO 15011-2:2009 defines laboratory methods for measuring the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) generated during arc welding, cutting and gouging, using a hood technique. The methodology is suitable for use with all open arc welding processes, cutting and gouging, but different designs of hood are used depending on the process and whether or not it can be conducted automatically.

Replaced standards (1)
NF EN ISO 15011-2
July 2003
Standard Cancelled
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2 : determination of emission rates of gases, except ozone

<p>ISO 15011-2:2003 provides guidance on the determination of emission rates of gases generated by arc welding using a fume box technique. It describes the test principle, gives a possible fume box arrangement and considers methods for sampling and analysis.</p> <p>The following gases that can be produced during arc welding are covered:</p> <p>- carbon monoxide (CO);</p> <p>- carbon dioxide (CO<sub>2</sub>);</p> <p>- nitrogen oxide (NO);</p> <p>- nitrogen dioxide (NO<sub>2</sub>).</p> <p>The fume box described in this International Standard may also be used for the determination of organic gases produced in the arc welding of coated metals, e.g. primed, painted or plastic coated material.</p>

Table of contents
View the extract
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    1
  • 4 Principe
    2
  • 5 Équipements et matériaux
    2
  • 6 Modes opératoires
    4
  • 6.1 Choix du mode opératoire de soudage
    4
  • 6.2 Montage du matériel d'essai
    5
  • 6.3 Essai à blanc
    5
  • 6.4 Soudage manuel à l'arc avec électrode enrobée
    5
  • 6.5 Procédés de soudage en continu avec fil et soudage TIG autogène
    6
  • 6.6 Coupage et gougeage
    7
  • 7 Calcul et expression des résultats
    8
  • Annexe A (informative) Exemples de conception de hotte
    9
  • Annexe B (informative) Notes relatives au matériel
    11
  • Annexe C (informative) Paramètres de soudage pour le soudage au gaz sous protection gazeuse
    13
  • Annexe D (normative) Modes opératoires
    16
  • Annexe E (normative) Calcul de la concentration stable moyenne de gaz
    17
  • Annexe F (normative) Rapport d'essai
    18
  • Bibliographie
    19
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ