NF EN ISO 15610

Afnor EDITIONS
Standards
NF EN ISO 15610

NF EN ISO 15610

May 2004

Standard Cancelled

Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables

ISO 15610:2003 gives the necessary information to explain the requirements referenced in ISO 15607 concerning the qualification of welding procedures based on tested consumables. In addition, it gives the range of qualification. ISO 15610:2003 applies to arc and gas welding but other fusion welding processes may be accepted if specified. It is limited to application to parent metals that produce acceptable micro structures and properties in the heat affected zone and which do not deteriorate significantly in service. This International Standard is not applicable where requirements for hardness or impact properties, preheating, controlled heat input, interpass temperature and post-weld heat-treatment are specified for the welded joint. The use of ISO 15610.2003 may also be restricted by an application standard or a specification.

View the extract

Main informations

Collections

National standards and national normative documents

Publication date

May 2004

Number of pages

12 p.

Reference

NF EN ISO 15610

ICS Codes

25.160.10 Welding processes

Classification index

A89-053

Print number

1 - 04/06/2004

International kinship

ISO 15610:2003

European kinship

EN ISO 15610:2003

Sumary

Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables

ISO 15610:2003 applies to arc and gas welding but other fusion welding processes may be accepted if specified.

It is limited to application to parent metals that produce acceptable micro structures and properties in the heat affected zone and which do not deteriorate significantly in service.

This International Standard is not applicable where requirements for hardness or impact properties, preheating, controlled heat input, interpass temperature and post-weld heat-treatment are specified for the welded joint.

The use of ISO 15610.2003 may also be restricted by an application standard or a specification.

Replaced standards (1)

NF EN 288-5

November 1994

Standard Cancelled

Specification and approval of welding procedures for metallic materials. Part 5 : approval by using approved welding consumables for arc welding.

Le présent document spécifie les conditions de qualification d'un mode opératoire de soudage par utilisation de produits consommables de soudage agréés pour le soudage à l'arc, et donne le domaine de validité de la qualification ainsi que sa durée.

Standard replaced by (1)

NF EN ISO 15610

February 2023

Standard Current

Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables

This document specifies how a welding procedure can be qualified by using tested welding consumable data. It expands on the requirements given in ISO 15607. In addition, it gives the range of qualification. Application of this document is limited to parent material groups 1.1, 8.1, 21, 22.1 and 22.2 in accordance with ISO/TR 15608, which produce acceptable microstructures and properties in the heat-affected zone which do not deteriorate significantly in service. This document is limited to: — parent material thicknesses t ≤ 40 mm (groups 1.1 and 8.1) and t ≤ 20 mm (groups 21, 22.1 and 22.2); — fillet welds with throat thickness a ≥ 1 mm. This document is not applicable when any of the following is specified for the welded joint: a) hardness; b) impact properties; c) preheating; d) controlled heat input; e) interpass temperature; f) post-weld heat treatment. The use of this document can also be restricted by an application standard, specification or other documents.

Table of contents

View the extract

Avant-propos
3
Introduction
4
1
Domaine d'application 4
2
Références normatives 5
3
Termes et définitions 5
4
Descriptifs de modes opératoires de soudage préliminaires (DMOS-P) 5
5
Qualification du mode opératoire de soudage 5
6
Domaine de validité 6
7
Validité 7
8
Procès-verbal d'un mode opératoire de soudage (PV-QMOS) 7
Bibliographie
8

ZOOM ON ... the Requirements department

To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!

Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ