ISO 2063:2005 applies to thermal-sprayed metallic coatings for the protection of iron and steel against corrosion by applying zinc or aluminium or their alloys to uncoated surfaces to be protected. This International Standard deals with characteristic properties and gives test methods for coatings obtained by the spraying of zinc and aluminium and their alloys for the general purpose of corrosion protection. It gives firstly the definition, classification and symbols for these coatings in relation to their thickness. It then deals with the preparation of surfaces, application of coatings and their characteristic properties: namely, thickness, appearance and adhesion. Finally ISO 2063:2005 gives test methods for checking these properties.
ISO 2063:2005 applies to thermal-sprayed metallic coatings for the protection of iron and steel against corrosion by applying zinc or aluminium or their alloys to uncoated surfaces to be protected.
This International Standard deals with characteristic properties and gives test methods for coatings obtained by the spraying of zinc and aluminium and their alloys for the general purpose of corrosion protection.
It gives firstly the definition, classification and symbols for these coatings in relation to their thickness.
It then deals with the preparation of surfaces, application of coatings and their characteristic properties: namely, thickness, appearance and adhesion.
Finally ISO 2063:2005 gives test methods for checking these properties.
<p>ISO 2063-2:2017 specifies requirements for corrosion protection of steel structures, components or parts, which are coated by thermal spraying of zinc, aluminium or their alloys.</p> <p>ISO 2063-2:2017 specifies requirements for coating manufacturers of surface preparation, thermal spraying, testing and post treatments, e.g. sealing of the coating. ISO 2063-2:2017 applies to metallic corrosion protection coatings in the case of new fabrication in the workshop, as well as on-site and for repair on-site after assembly.</p> <p>Requirements for coating thickness, minimum adhesive strength and surface conditions, specified in a coating specification, are given.</p> <p>Recommendations are given for suitable process steps and quality assurance measures for new production and maintenance and for supervising of corrosion protection works.</p> <p>ISO 2063-2:2017 covers the application of thermal-sprayed zinc, aluminium and their alloys for protection against corrosion in the temperature range between ?50 °C to +200 °C. Heat-resistant protective coatings of aluminium are covered by ISO 17834 and are not in the scope of ISO 2063-2:2017.</p> <p>ISO 2063-2:2017 specifies requirements for the equipment, the working place and the qualification of the spray and testing personnel.</p> <p>NOTE ISO 2063‑1:2017 is addressed to the designer and to the planning engineer of corrosion protection system.</p>
<p>ISO 2063-1:2017 specifies requirements for the protection of iron and steel surfaces against corrosion by applying thermal-sprayed metallic coatings of zinc, aluminium or their alloys.</p> <p>In ISO 2063-1:2017, requirements for the planning of the corrosion protection system and for the constructive design of the component to be protected are specified, where thermal spraying is intended to be the process for the deposition of the metallic corrosion protection.</p> <p>Some field-related basic terms are defined and instructions for corrosion behaviour of the zinc and aluminium materials under different environment conditions are provided.</p> <p>Characteristic properties of the coating, e.g. coating thickness, minimum adhesive strength and surface appearance, are specified and test procedures for thermal-sprayed corrosion protection coatings of zinc, aluminium or their alloys are determined.</p> <p>ISO 2063-1:2017 is valid for applying thermal-sprayed zinc and aluminium protection coatings against corrosion in the temperature range between ?50 °C to +200 °C, taking into consideration the service conditions of any sealants used. Heat-resistant protective coatings of aluminium are covered by ISO 17834 and are not in the scope of ISO 2063-1:2017.</p> <p>Other corrosion protection processes, e.g. hot-dip galvanizing (galvanic coating), sherardizing, electroplating or selection and deposition of organic coatings/paints are not in the scope of ISO 2063-1:2017.</p> <p>Requirements for the manufacturing of thermal-sprayed coatings are specified in ISO 2063‑2.</p>
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ