NF EN ISO 4414

NF EN ISO 4414

March 2011
Standard Current

Pneumatic fluid power - General rules and safety requirements for systems and their components

ISO 4414:2010 specifies general rules and safety requirements for pneumatic fluid power systems and components used on machinery as defined by ISO 12100. ISO 4414:2010 deals with all significant hazards associated with pneumatic fluid power systems and specifies principles to apply in order to avoid those hazards when the systems are put to their intended use. ISO 4414:2010 applies to the design, construction and modification of systems and their components, also taking into account the following aspects: assembly, installation, adjustment, uninterrupted system operation, ease and economy of maintenance and cleaning, reliable operation in all intended uses, energy efficiency and environment. ISO 4414:2010 does not apply to air compressors and the systems associated with air distribution as typically installed in a factory, including gas bottles and receivers.

See more
Document attached to the standard

One or more files are associated with this standard. After your purchase, you will find it (them) directly from your customer area, in the same place as the standard.

Main informations

Collections

National standards and national normative documents

Publication date

March 2011

Number of pages

50 p.

Reference

NF EN ISO 4414

ICS Codes

23.100.01   Fluid power systems in general

Classification index

E49-201

Print number

1 - 17/02/2011

International kinship

ISO 4414:2010

European kinship

EN ISO 4414:2010
Sumary
Pneumatic fluid power - General rules and safety requirements for systems and their components

ISO 4414:2010 specifies general rules and safety requirements for pneumatic fluid power systems and components used on machinery as defined by ISO 12100. ISO 4414:2010 deals with all significant hazards associated with pneumatic fluid power systems and specifies principles to apply in order to avoid those hazards when the systems are put to their intended use.

ISO 4414:2010 applies to the design, construction and modification of systems and their components, also taking into account the following aspects: assembly, installation, adjustment, uninterrupted system operation, ease and economy of maintenance and cleaning, reliable operation in all intended uses, energy efficiency and environment.

ISO 4414:2010 does not apply to air compressors and the systems associated with air distribution as typically installed in a factory, including gas bottles and receivers.

Replaced standards (2)
NF ISO 4414
August 1999
Standard Cancelled
Pneumatic fluid power. General rules relating to systems.

<p> La présente Norme internationale fournit des règles générales relatives aux systèmes pneumatiques des machines utilisées dans les procédés de fabrication industrielle. Elle est destinée à servir de guide à la fois aux fournisseurs et aux acheteurs, afin d'assurer : a) la sécurité ; b) un fonctionnement continu du système ; c) une maintenance facile et économique ; d) la pérennité du système. La présente Norme internationale ne s'applique pas aux compresseurs d'air et aux systèmes associés à la distribution d'air généralement installés dans une usine. </p>

NF EN 983+A1
November 2008
Standard Cancelled
Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics

Le présent document spécifie les principes généraux de conception et de construction des systèmes et composants pneumatiques et ce à l'usage des constructeurs, concepteurs et autres parties intéressées. Il vient à l'appui des exigences essentielles de sécurité des Directives "Machines" 98/37/CE (voir Annexe ZA) et 2006/42/CE (voir Annexe ZB).

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    2
  • 4 Liste des phénomènes dangereux significatifs
    2
  • 5 Règles générales et exigences de sécurité
    3
  • 5.1 Généralités
    3
  • 5.2 Exigences fondamentales relatives à la conception et à la spécification des systèmes pneumatiques
    3
  • 5.3 Exigences supplémentaires
    6
  • 5.4 Exigences spécifiques relatives aux composants et aux commandes
    7
  • 6 Vérification des exigences de sécurité et essais de réception
    18
  • 7 Informations pour l'utilisation
    19
  • 7.1 Exigences générales
    19
  • 7.2 Documentation finale
    19
  • 7.3 Consignes de maintenance et d'utilisation
    19
  • 7.4 Marquage et identification
    20
  • 8 Phrase d'identification (référence à la présente Norme internationale)
    24
  • Annexe A (informative) Liste des phénomènes dangereux significatifs
    25
  • Annexe B (informative) Formulaire pour recueillir les données relatives au système pneumatique et à ses composants afin de vérifier la conformité à l'ISO 4414
    28
  • Bibliographie
    39
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ