NF EN ISO 6847

NF EN ISO 6847

September 2013
Standard Cancelled

Welding consumables - Deposition of a weld metal pad for chemical analysis

ISO 6847:2013 specifies the procedure to be used for deposition of a weld metal pad for chemical analysis. ISO 6847:2013 applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for non-gas shielded metal arc welding, tubular cored rods for gas tungsten arc welding, and wire-flux combinations for submerged arc welding. ISO 6847:2013 is applicable to welding consumables for non-alloy and fine grain steels, high strength steels, creep-resisting steels, stainless and heat-resisting steels, nickel and nickel alloys, and copper and copper alloys.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

September 2013

Number of pages

14 p.

Reference

NF EN ISO 6847

ICS Codes

25.160.20   Welding consumables

Classification index

A81-304

Print number

1 - 19/08/2013

International kinship

ISO 6847

European kinship

EN ISO 6847:2013
Sumary
Welding consumables - Deposition of a weld metal pad for chemical analysis

ISO 6847:2013 specifies the procedure to be used for deposition of a weld metal pad for chemical analysis. ISO 6847:2013 applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for non-gas shielded metal arc welding, tubular cored rods for gas tungsten arc welding, and wire-flux combinations for submerged arc welding. ISO 6847:2013 is applicable to welding consumables for non-alloy and fine grain steels, high strength steels, creep-resisting steels, stainless and heat-resisting steels, nickel and nickel alloys, and copper and copper alloys.

Replaced standards (1)
NF EN ISO 6847
August 2002
Standard Cancelled
Welding consumables - Deposition of a weld metal pad for chemical analysis

Le présent document spécifie le mode opératoire à utiliser pour réaliser un dépôt de soudure pour l'analyse chimique.

Standard replaced by (1)
NF EN ISO 6847
September 2020
Standard Current
Welding consumables - Deposition of a weld metal pad for chemical analysis

<p>This document specifies the procedure to be used for deposition of a weld metal pad for chemical analysis.</p> <p>This document applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for non-gas shielded metal arc welding, solid rods and tubular cored rods for gas tungsten arc welding, and wire-flux and strip-flux combinations for submerged arc welding or electroslag welding and cladding.</p> <p>This document is applicable to welding consumables for non-alloy and fine grain steels, high strength steels, creep-resisting steels, stainless and heat-resisting steels, nickel and nickel alloys, and copper and copper alloys.</p>

Table of contents
View the extract
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Métal de base
    1
  • 3.1 Type
    1
  • 3.2 Dimensions
    1
  • 3.3 État de surface
    1
  • 4 Méthode de préparation des blocs de métal fondu
    2
  • 4.1 Étuvage des produits consommables pour le soudage
    2
  • 4.2 Position de soudage
    2
  • 4.3 Type de courant
    2
  • 4.4 Conditions de soudage
    2
  • 4.5 Méthode de soudage
    2
  • 5 Dimensions du bloc de métal fondu
    3
  • 6 Échantillonnage
    4
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
What is the Redline format?
The Redline + service - standards comparator allows you to easily and simply identify major changes between the current standard and its last canceled version.

At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.
At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula

The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.

For an overview of the service, click on View a standard in redline format
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ