NF ISO 1268-1

NF ISO 1268-1

September 2002
Standard Current

Fibre-reinforced plastics - Methods of producing test plates - Part 1 : general conditions

The various parts of ISO 1268 (see the foreword) describe methods used to prepare reinforced-plastics plates from which test specimens can be cut. This allows the properties of a composite, or the constituents of the composite, to be determined. The methods are intended to cover all the main types of reinforcement and resin matrix. The choice of test plate preparation method depends on: a) the reinforcement:  its nature (glass, carbon, aramid, etc.);  its form (roving, mat, woven fabric, etc.);  its orientation with respect to the length, width and thickness of the plate;  its content in the reinforced plastic; b) the matrix (thermosetting or thermoplastic); c) the magnitude expected for the properties; d) the production process that is to be evaluated. Since the mechanical properties of a reinforced plastic are known to be dependent on the process by which the plastic is produced, it is recommended that the test plates be prepared, if possible, by the same method that will be used to produce the plastic. This part of ISO 1268 describes the general requirements common to all the methods.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

September 2002

Number of pages

8 p.

Reference

NF ISO 1268-1

ICS Codes

83.120   Reinforced plastics

Classification index

T57-153-1

Print number

1 - 07/12/2002

International kinship

ISO 1268-1:2001
Sumary
Fibre-reinforced plastics - Methods of producing test plates - Part 1 : general conditions

The various parts of ISO 1268 (see the foreword) describe methods used to prepare reinforced-plastics plates from

which test specimens can be cut. This allows the properties of a composite, or the constituents of the composite, to

be determined. The methods are intended to cover all the main types of reinforcement and resin matrix.

The choice of test plate preparation method depends on:

a) the reinforcement:

 its nature (glass, carbon, aramid, etc.);

 its form (roving, mat, woven fabric, etc.);

 its orientation with respect to the length, width and thickness of the plate;

 its content in the reinforced plastic;

b) the matrix (thermosetting or thermoplastic);

c) the magnitude expected for the properties;

d) the production process that is to be evaluated.

Since the mechanical properties of a reinforced plastic are known to be dependent on the process by which the

plastic is produced, it is recommended that the test plates be prepared, if possible, by the same method that will be

used to produce the plastic.

This part of ISO 1268 describes the general requirements common to all the methods.

Replaced standards (1)
NF T57-153
October 1973
Published document Cancelled
Plastics materials reinforced with textile glass. Preparation of glass fibre reinforced, resin bonded, low-pressure laminated plates or panels for test purposes.

Table of contents
View the extract
  • Avant-propos
    iv
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    2
  • 4 Hygiène et sécurité
    2
  • 5 Principes
    2
  • 6 Matières premières et produits semi-finis
    2
  • 7 Dimensions des plaques
    2
  • 8 Renfort
    2
  • 9 Prescriptions générales relatives à l'appareillage utilisé dans le laboratoire ou l'atelier
    3
  • 10 Modes opératoires
    3
  • 11 Vérification des caractéristiques de la plaque obtenue
    3
  • 12 Marquage
    3
  • 13 Rapport de fabrication de plaque(s)
    4
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ