NF ISO 2878

NF ISO 2878

December 2005
Standard Cancelled

Rubber - Antistatic and conductive products - Determination of electrical resistance

ISO 2878:2005 specifies a method of determining the electrical resistance of antistatic and conductive products manufactured wholly or in part from rubber whose electrical resistance measured between defined points, when new, does not exceed 3 times 108 ohms and whose conductivity is derived from the addition of carbon black and/or other appropriate substances to the bulk of the material. This International Standard specifies the electrode configuration for basic geometries but reference should be made to relevant product specifications for requirements for specific products. It does not apply to: products were the relevant surfaces are composed of mixtures of insulating and conductive areas;products with a substantial surface area of insulating material (except for footwear, which does not normally have a conductive or antistatic upper).

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

December 2005

Number of pages

12 p.

Reference

NF ISO 2878

ICS Codes

83.060   Rubber

Classification index

T47-132

Print number

1 - 22/12/2005

International kinship

ISO 2878:2005
Sumary
Rubber - Antistatic and conductive products - Determination of electrical resistance

ISO 2878:2005 specifies a method of determining the electrical resistance of antistatic and conductive products manufactured wholly or in part from rubber whose electrical resistance measured between defined points, when new, does not exceed 3 times 108 ohms and whose conductivity is derived from the addition of carbon black and/or other appropriate substances to the bulk of the material.

This International Standard specifies the electrode configuration for basic geometries but reference should be made to relevant product specifications for requirements for specific products.

It does not apply to:

  1. products were the relevant surfaces are composed of mixtures of insulating and conductive areas;
  2. products with a substantial surface area of insulating material (except for footwear, which does not normally have a conductive or antistatic upper).
Replaced standards (1)
T47-132
May 1973
Standard Cancelled
Antistatic and conductive rubber products. Determination of electrical resistance.

Standard replaced by (1)
NF ISO 2878
November 2011
Standard Cancelled
Rubber, vulcanized or thermoplastic - Antistatic and conductive products - Determination of electrical resistance

<p>ISO 2878:2011 specifies a method of test to determine the electrical resistance of antistatic and conductive products manufactured wholly or in part from rubber whose electrical resistance measured between defined points, when new, does not exceed 3 x 10<sup>8</sup> ohms and whose conductivity is derived from the addition of carbon black and/or other appropriate substances to the bulk of the material.</p> <p>It specifies the electrode configuration for basic geometries, but reference should be made to relevant product specifications for requirements for specific products.</p> <p>It does not apply to:</p> <ol> <li>products the relevant surfaces of which are composed of mixtures of insulating and conductive areas;</li> <li>products with a substantial surface area of insulating material, except for footwear (which does not normally have a conductive or antistatic upper).</li> </ol>

Table of contents
View the extract
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Principes
    2
  • 4 Appareillage
    2
  • 5 Conditions d'essai
    3
  • 6 Mode opératoire
    4
  • 7 Détails concernant les modes opératoires applicables aux différents produits
    4
  • 8 Rapport d'essai
    6
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ