ISO 3951-1:2013 specifies an acceptance sampling system of single sampling plans for inspection by variables. It is indexed in terms of the acceptance quality limit (AQL) and is designed for users who have simple requirements. (A more comprehensive and technical treatment is given in ISO 3951-2.) ISO 3951-1:2013 is complementary to ISO 2859-1. The objectives of the methods laid down in ISO 3951-1:2013 are to ensure that lots of acceptable quality have a high probability of acceptance and that the probability of not accepting inferior lots is as high as practicable. This is achieved by means of the switching rules, which provide the following: an automatic protection to the consumer (by means of a switch to tightened inspection or discontinuation of sampling inspection) should a deterioration in quality be detected; an incentive (at the discretion of the responsible authority) to reduce inspection costs (by means of a switch to a smaller sample size) should consistently good quality be achieved. In ISO 3951-1:2013, the acceptability of a lot is implicitly determined from an estimate of the percentage of nonconforming items in the process, based on a random sample of items from the lot. ISO 3951-1:2013 is intended for application to a continuing series of lots of discrete products all supplied by one producer using one production process. If there are different producers or production processes, ISO 3951-1:2013 is applied to each one separately. ISO 3951-1:2013 is intended for application to a single quality characteristic that is measurable on a continuous scale. For two or more such quality characteristics, see ISO 3951-2.
ISO 3951-1:2013 specifies an acceptance sampling system of single sampling plans for inspection by variables. It is indexed in terms of the acceptance quality limit (AQL) and is designed for users who have simple requirements. (A more comprehensive and technical treatment is given in ISO 3951-2.) ISO 3951-1:2013 is complementary to ISO 2859-1.
The objectives of the methods laid down in ISO 3951-1:2013 are to ensure that lots of acceptable quality have a high probability of acceptance and that the probability of not accepting inferior lots is as high as practicable. This is achieved by means of the switching rules, which provide the following:
In ISO 3951-1:2013, the acceptability of a lot is implicitly determined from an estimate of the percentage of nonconforming items in the process, based on a random sample of items from the lot.
ISO 3951-1:2013 is intended for application to a continuing series of lots of discrete products all supplied by one producer using one production process. If there are different producers or production processes, ISO 3951-1:2013 is applied to each one separately.
ISO 3951-1:2013 is intended for application to a single quality characteristic that is measurable on a continuous scale. For two or more such quality characteristics, see ISO 3951-2.
<p>This document specifies single sampling plans for lot-by-lot inspection under the following conditions:</p> <p>a) where the inspection procedure is applied to a continuing series of lots of discrete products, all supplied by one producer using one production process;</p> <p>b) where only a single quality characteristic, <em>x</em>, of these products is taken into consideration, which is measurable on a continuous scale;</p> <p>c) where production is under statistical control and the quality characteristic, <em>x</em>, is distributed according to a normal distribution or a close approximation to the normal distribution;</p> <p>d) where a contract or standard defines a lower specification limit, <em>L</em>, an upper specification limit, <em>U</em>, or both. An item is qualified as conforming if its measured quality characteristic, <em>x,</em> satisfies as appropriate one of the following inequalities:</p> <p>1) <em>x</em> ≥ <em>L</em> (i.e. the lower specification limit is not violated);</p> <p>2) <em>x</em> ≤ <em>U</em> (i.e. the upper specification limit is not violated);</p> <p>3) <em>x ≥ L</em> and <em>x</em> ≤ <em>U</em> (i.e. neither the lower nor the upper specification limit is violated).</p> <p>Inequalities 1) and 2) are cases with a single specification limit, and 3) is a case with double specification limits.</p> <p>Where double specification limits apply, it is assumed in this document that conformity to both specification limits is equally important to the integrity of the product. In such cases, it is appropriate to apply a single AQL to the combined percentage of a product outside the two specification limits. This is referred to as combined control.</p>
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ