NF ISO 7619-1

NF ISO 7619-1

December 2010
Standard Cancelled

Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 1 : durometer method (Shore hardness)

ISO 7619-1:2010 specifies a method for determining the indentation hardness (Shore hardness) of vulcanized or thermoplastic rubber by means of durometers using the A scale for rubbers in the normal-hardness range; the D scale for rubbers in the high-hardness range; the AO scale for rubbers in the low-hardness range and for cellular rubbers; and the AM scale for thin rubber test pieces in the normal-hardness range.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

December 2010

Number of pages

18 p.

Reference

NF ISO 7619-1

ICS Codes

83.060   Rubber

Classification index

T46-052-1

Print number

1 - 22/11/2010

International kinship

ISO 7619-1:2010
Sumary
Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 1 : durometer method (Shore hardness)

ISO 7619-1:2010 specifies a method for determining the indentation hardness (Shore hardness) of vulcanized or thermoplastic rubber by means of durometers using the A scale for rubbers in the normal-hardness range; the D scale for rubbers in the high-hardness range; the AO scale for rubbers in the low-hardness range and for cellular rubbers; and the AM scale for thin rubber test pieces in the normal-hardness range.

Replaced standards (2)
NF ISO 7619-1
March 2006
Standard Cancelled
Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 1 : durometer method (Shore hardness)

Le présent document spécifie une méthode de détermination de la dureté (Shore) des caoutchoucs vulcanisés ou des caoutchoucs thermoplastiques par pénétration au moyen de duromètres. La méthode au duromètre de poche fait l'objet de la partie 2.

NF ISO 7619-1/A1
December 2008
Standard Cancelled
Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 1 : durometer method (Shore hardness) - AMENDMENT 1 : precision data

Standard replaced by (1)
NF ISO 48-4
December 2018
Standard Current
Rubber, vulcanized or thermoplastic - Determination of hardness - Part 4 : indentation hardness by durometer method (Shore hardness)

<p>This document specifies a method for determining the indentation hardness (Shore hardness) of vulcanized or thermoplastic rubber using durometers with the following scales:</p> <p>— the A scale for rubbers in the normal-hardness range;</p> <p>— the D scale for rubbers in the high-hardness range;</p> <p>— the AO scale for rubbers in the low-hardness range and for cellular rubbers;</p> <p>— the AM scale for thin rubber test pieces in the normal-hardness range.</p>

Table of contents
View the extract
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Principe et choix du type de duromètre
    1
  • 4 Appareillage
    2
  • 4.1 Duromètres de types A, D et AO
    2
  • 4.2 Duromètre de type AM
    4
  • 4.3 Support
    4
  • 4.4 Étalonnage de la force du ressort du duromètre
    5
  • 5 Éprouvettes
    5
  • 5.1 Généralités
    5
  • 5.2 Épaisseur
    5
  • 5.3 Surface
    6
  • 6 Température de conditionnement et d'essai
    6
  • 7 Mode opératoire
    6
  • 7.1 Généralités
    6
  • 7.2 Temps d'essai
    6
  • 7.3 Mesurages
    7
  • 8 Étalonnage et vérification
    7
  • 8.1 Étalonnage
    7
  • 8.2 Vérification à l'aide de blocs de caoutchouc de référence
    7
  • 9 Fidélité
    7
  • 10 Rapport d'essai
    7
  • Annexe A (informative) Fidélité des mesurages de dureté avec un duromètre de type AM comparée à la fidélité des mesurages de microdureté DIDC
    9
  • Bibliographie
    12
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ