ISO 20904:2020
Hard coal - Sampling of slurries
This document sets out the basic methods for sampling fine coal, coal rejects or tailings of nominal top size <4 mm that is mixed with water to form a slurry. At very high ratios of fine solids to water when the material assumes a soft plastic form, the mixture is correctly termed a paste. Sampling of pastes is not covered in this document. The procedures described in this document primarily apply to sampling of coal that is transported in moving streams as a slurry. These streams can fall freely or be confined in pipes, launders, chutes, spirals or similar channels. Sampling of slurries in stationary situations, such as a settled or even a well-stirred slurry in a tank, holding vessel or dam, is not recommended and is not covered in this Document. This document describes procedures that are designed to provide samples representative of the slurry solids and particle size distribution of the slurry under examination. After draining the slurry sample of fluid and measuring the fluid volume, damp samples of the contained solids in the slurry are available for drying (if required) and measurement of one or more characteristics in an unbiased manner and with a known degree of precision. The characteristics are measured by chemical analysis or physical testing or both. The sampling methods described are applicable to slurries that require inspection to verify compliance with product specifications, determination of the value of a characteristic as a basis for settlement between trading partners or estimation of a set of average characteristics and variances that describes a system or procedure. Provided flow rates are not too high, the reference method against which other sampling procedures are compared is one where the entire stream is diverted into a vessel for a specified time or volume interval. This method corresponds to the stopped-belt method described in ISO 13909-2.
This document sets out the basic methods for sampling fine coal, coal rejects or tailings of nominal top size <4 mm that is mixed with water to form a slurry. At very high ratios of fine solids to water when the material assumes a soft plastic form, the mixture is correctly termed a paste. Sampling of pastes is not covered in this document.
The procedures described in this document primarily apply to sampling of coal that is transported in moving streams as a slurry. These streams can fall freely or be confined in pipes, launders, chutes, spirals or similar channels. Sampling of slurries in stationary situations, such as a settled or even a well-stirred slurry in a tank, holding vessel or dam, is not recommended and is not covered in this Document.
This document describes procedures that are designed to provide samples representative of the slurry solids and particle size distribution of the slurry under examination. After draining the slurry sample of fluid and measuring the fluid volume, damp samples of the contained solids in the slurry are available for drying (if required) and measurement of one or more characteristics in an unbiased manner and with a known degree of precision. The characteristics are measured by chemical analysis or physical testing or both.
The sampling methods described are applicable to slurries that require inspection to verify compliance with product specifications, determination of the value of a characteristic as a basis for settlement between trading partners or estimation of a set of average characteristics and variances that describes a system or procedure.
Provided flow rates are not too high, the reference method against which other sampling procedures are compared is one where the entire stream is diverted into a vessel for a specified time or volume interval. This method corresponds to the stopped-belt method described in ISO 13909-2.
<p>ISO 20904:2006 sets out the basic methods for sampling fine coal, coal rejects or tailings of nominal top size < 4 mm that is mixed with water to form a slurry. At very high ratios of fine solids to water when the material assumes a soft plastic form, the mixture is correctly termed a paste. Sampling of pastes is not covered in ISO 20904:2006.</p> <p>The procedures described in ISO 20904:2006 primarily apply to sampling of coal that is transported in moving streams as a slurry. These streams can fall freely or be confined in pipes, launders, chutes, spirals or similar channels. Sampling of slurries in stationary situations, such as a settled or even a well-stirred slurry in a tank, holding vessel or dam, is not recommended and is not covered in ISO 20904:2006.</p> <p>ISO 20904:2006 describes procedures that are designed to provide samples representative of the slurry solids and particle size distribution of the slurry under examination. After draining the slurry sample of fluid and measuring the fluid volume, damp samples of the contained solids in the slurry are available for drying (if required) and measurement of one or more characteristics in an unbiased manner and with a known degree of precision. The characteristics are measured by chemical analysis or physical testing or both.</p> <p>The sampling methods described are applicable to slurries that require inspection to verify compliance with product specifications, determination of the value of a characteristic as a basis for settlement between trading partners or estimation of a set of average characteristics and variances that describes a system or procedure.</p>
The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.
The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.
With Requirements, quickly access the main part of the normative text!
At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.
The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.
For an overview of the service, click on View a standard in redline format
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ