NF EN ISO 13628-10
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10 : specification for bonded flexible pipe
ISO 13628-10:2005 defines the technical requirements for safe, dimensionally and functionally interchangeable bonded flexible pipes that are designed and manufactured to uniform standards and criteria. Minimum requirements are specified for the design, material selection, manufacture, testing, marking and packaging of bonded flexible pipes, with reference to existing codes and standards where applicable. ISO 13628-10:2005 applies to bonded flexible pipe assemblies, consisting of segments of flexible pipe body with end fittings attached to both ends. ISO 13628-10:2005 applies to pipes with a design pressure greater than or equal to 1,5 MPa (15 bar). ISO 13628-10:2005 can be used for lower design pressure pipes, though the requirements of these pipes have not been specifically addressed. ISO 13628-10:2005 does not cover flexible pipes of unbonded structure nor to flexible pipe ancillary components and does not apply to flexible pipes for use in choke and kill line applications.. ISO 13628-10:2005 can be applied to flexible pipes that include non-metallic reinforcing layers, though no effort was made to address the specific and unique technological aspects of this product, and to a bonded construction pipe that includes a material or layer construction that is covered in ISO 13628-2. ISO 13628-10:2005 can be applied to flexible pipes for pile hammer, gas flare, water supply and jetting applications, though no effort was made to address the specific and unique technological aspects relating to each of these requirements.
ISO 13628-10:2005 defines the technical requirements for safe, dimensionally and functionally interchangeable bonded flexible pipes that are designed and manufactured to uniform standards and criteria. Minimum requirements are specified for the design, material selection, manufacture, testing, marking and packaging of bonded flexible pipes, with reference to existing codes and standards where applicable.
ISO 13628-10:2005 applies to bonded flexible pipe assemblies, consisting of segments of flexible pipe body with end fittings attached to both ends.
ISO 13628-10:2005 applies to pipes with a design pressure greater than or equal to 1,5 MPa (15 bar). ISO 13628-10:2005 can be used for lower design pressure pipes, though the requirements of these pipes have not been specifically addressed.
ISO 13628-10:2005 does not cover flexible pipes of unbonded structure nor to flexible pipe ancillary components and does not apply to flexible pipes for use in choke and kill line applications..
ISO 13628-10:2005 can be applied to flexible pipes that include non-metallic reinforcing layers, though no effort was made to address the specific and unique technological aspects of this product, and to a bonded construction pipe that includes a material or layer construction that is covered in ISO 13628-2.
ISO 13628-10:2005 can be applied to flexible pipes for pile hammer, gas flare, water supply and jetting applications, though no effort was made to address the specific and unique technological aspects relating to each of these requirements.
- Avant-proposv
- Introductionvi
-
1 Domaine d'application1
-
1.1 Objet1
-
1.2 Produits2
-
1.3 Applications2
-
2 Références normatives2
-
3 Termes, définitions et abréviations5
-
3.1 Termes et définitions5
-
3.2 Symboles et abréviations11
-
4 Exigences relatives au fonctionnement12
-
4.1 Généralités12
-
4.2 Exigences globales12
-
4.3 Paramètres généraux de conception13
-
4.4 Paramètres relatifs aux fluides internes13
-
4.5 Environnement extérieur15
-
4.6 Exigences système15
-
5 Exigences de conception19
-
5.1 Charges et effets de charges19
-
5.2 Méthodologie de conception des canalisations22
-
5.3 Conception de la structure de la canalisation23
-
5.4 Exigences relatives à la conception du système28
-
6 Matériaux32
-
6.1 Exigences relatives aux matériaux32
-
6.2 Exigences de qualification36
-
6.3 Exigences d'assurance de la qualité44
-
7 Exigences de fabrication46
-
7.1 Exigences d'assurance de la qualité46
-
7.2 Carcasse47
-
7.3 Préparation de la composition et calandrage48
-
7.4 Enroulement de l'élastomère49
-
7.5 Couche d'armature de renforcement50
-
7.6 Couches d'isolation50
-
7.7 Raccord d'extrémité50
-
7.8 Procédé de durcissement52
-
7.9 Procédés spéciaux53
-
7.10 Tolérances de fabrication55
-
7.11 Réparations55
-
8 Documentation56
-
8.1 Généralités56
-
8.2 Principes de conception56
-
8.3 Rapport des charges de calcul56
-
8.4 Rapport de conception57
-
8.5 Plan qualité de fabrication58
-
8.6 Spécification de fabrication58
-
8.7 Documentation conforme à l'exécution58
-
8.8 Manuel d'exploitation59
-
9 Essais de réception en usine60
-
9.1 Généralités60
-
9.2 Essai dimensionnel61
-
9.3 Essai de pression hydrostatique61
-
9.4 Essais de continuité et de résistance électrique62
-
9.5 Essai au kérosène62
-
9.6 Essai de tenue au vide62
-
10 Marquage et conditionnement63
-
10.1 Marquage63
-
10.2 Emballage64
- Annexe A (informative) Lignes directrices d'achat65
- Annexe B (informative) Raidisseurs anti-courbure et limiteurs de courbure72
- Annexe C (informative) Utilisation du monogramme API77
- Bibliographie78
The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.
The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.
With Requirements, quickly access the main part of the normative text!
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ