NF ISO 8133
Hydraulic fluid power - Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series
ISO 8133:2014 specifies the mounting dimensions required for interchangeability of accessories for 16 MPa [160 bar)] compact cylinders conforming to ISO 6020-2. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020-2, but this does not limit their application. ISO 8133:2014 covers the following accessories, identified in accordance with ISO 6099: AP6 (rod eye spherical, female thread); AB5 (clevis bracket, spherical eye, in angle); AA6-L (pivot pin, spherical bearing, locking plate); AL6 (locking plate for pivot pin); AP2 (rod clevis, female thread); AP4 (rod eye plain, female thread); AB2 (eye bracket); AB4 (clevis bracket, straight); AA4-S (pivot pin, plain, split pins); AA4-R (pivot pin, plain, rings); AT4 (trunnion bracket). These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 3322. ISO 8133:2014 only applies to the dimensional criteria of products manufactured in conformity with this International Standard; it does not apply to their functional characteristics.
ISO 8133:2014 specifies the mounting dimensions required for interchangeability of accessories for 16 MPa [160 bar)] compact cylinders conforming to ISO 6020-2. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020-2, but this does not limit their application.
ISO 8133:2014 covers the following accessories, identified in accordance with ISO 6099: AP6 (rod eye spherical, female thread); AB5 (clevis bracket, spherical eye, in angle); AA6-L (pivot pin, spherical bearing, locking plate); AL6 (locking plate for pivot pin); AP2 (rod clevis, female thread); AP4 (rod eye plain, female thread); AB2 (eye bracket); AB4 (clevis bracket, straight); AA4-S (pivot pin, plain, split pins); AA4-R (pivot pin, plain, rings); AT4 (trunnion bracket).
These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 3322.
ISO 8133:2014 only applies to the dimensional criteria of products manufactured in conformity with this International Standard; it does not apply to their functional characteristics.
Le présent document spécifie les dimensions des accessoires pour vérins hydrauliques 16 MPa, série compacte conformes à la NF ISO 6020-2, afin d'assurer leur interchangeabilité.
<p>This document specifies the mounting dimensions required for interchangeability of accessories for 16 MPa (160 bar) compact cylinders conforming to ISO 6020‑2. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020‑2, but this does not limit their application[1].</p> <p>This document covers the following accessories, identified in accordance with ISO 6099:</p> <p>— AP6 — rod eye spherical, female thread (see Figure 1 and Table 1);</p> <p>— AB5 — clevis bracket, spherical eye, in angle (see Figure 2 and Table 2);</p> <p>— AA6-L — pivot pin, spherical bearing, locking plate (see Figure 3 and Table 3);</p> <p>— AL6 — locking plate for pivot pin (see Figure 4 and Table 4);</p> <p>— AP2 — rod clevis, female thread (see Figure 5 and Table 5);</p> <p>— AP4 — rod eye plain, female thread (see Figure 6 and Table 6);</p> <p>— AB2 — eye bracket (see Figure 7 and Table 7);</p> <p>— AB4 — clevis bracket, straight (see Figure 8 and Table 8);</p> <p>— AA4-S — pivot pin, plain (split pins) (see Figure 9 and Table 9);</p> <p>— AA4-R — pivot pin, plain (rings) (see Figure 10 and Table 10);</p> <p>— AT4 — trunnion bracket (see Figure 11 and Table 11).</p> <p>These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 2944.</p> <p>This document only applies to the dimensional criteria of products manufactured in conformity with this document; it does not apply to their functional characteristics.</p> <p> </p> <p>[1] 1 bar = 0,1 MPa = 10<sup>5</sup> Pa; 1 MPa = 1 N/mm<sup>2</sup></p>
- Avant-proposiv
- Introductionv
-
1 Domaine d'application1
-
2 Références normatives1
-
3 Termes et définitions2
-
4 Dimensions d'interchangeabilité2
-
5 Tolérances2
-
6 Instructions d'application2
-
7 Désignation3
-
8 Phrase d'identification (référence à la présente Norme internationale)4
- Bibliographie17
At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.
The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.
For an overview of the service, click on View a standard in redline format
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ