NF EN ISO 7250-1

NF EN ISO 7250-1

November 2017
Standard Current

Basic human body measurements for technological design - Part 1 : Body measurement definitions and landmarks

ISO 7250-1:2017 provides a description of anthropometric measurements which can be used as a basis for comparison of population groups and for the creation of anthropometric databases (see ISO 15535). The basic list of measurements specified in this document is intended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live. In addition, the list serves as a basis for extracting one- and two-dimensional measurements from three-dimensional scans (specified in ISO 20685). It serves as a guide on how to take anthropometric measurements, but also gives information to the ergonomist and designer on the anatomical and anthropometrical bases and principles of measurement which are applied in the solution of design tasks.ISO 7250-1:2017 is intended to be used in conjunction with national or international regulations or agreements to ensure harmony in defining population groups and to allow comparison of anthropometric data among member bodies. In its various applications, it is anticipated that the basic list will be supplemented by specific additional measurements. Annex A shows the correspondence of dimensions described here with their use in ISO 14738 and ISO 15534.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Thematics

Sécurité, Silver économie, Gestion des risques et SST, Accessibilité, QSE

Publication date

November 2017

Number of pages

61 p.

Reference

NF EN ISO 7250-1

ICS Codes

13.180   Ergonomics

Classification index

X35-003-1

Print number

1

International kinship

ISO 7250-1:2017

European kinship

EN ISO 7250-1:2017
Sumary
Basic human body measurements for technological design - Part 1 : Body measurement definitions and landmarks

ISO 7250-1:2017 provides a description of anthropometric measurements which can be used as a basis for comparison of population groups and for the creation of anthropometric databases (see ISO 15535). The basic list of measurements specified in this document is intended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live. In addition, the list serves as a basis for extracting one- and two-dimensional measurements from three-dimensional scans (specified in ISO 20685). It serves as a guide on how to take anthropometric measurements, but also gives information to the ergonomist and designer on the anatomical and anthropometrical bases and principles of measurement which are applied in the solution of design tasks.

ISO 7250-1:2017 is intended to be used in conjunction with national or international regulations or agreements to ensure harmony in defining population groups and to allow comparison of anthropometric data among member bodies. In its various applications, it is anticipated that the basic list will be supplemented by specific additional measurements. Annex A shows the correspondence of dimensions described here with their use in ISO 14738 and ISO 15534.

Replaced standards (1)
NF EN ISO 7250-1
June 2010
Standard Cancelled
Basic human body measurements for technological design - Part 1 : body measurement definitions and landmarks

ISO 7250-1:2008 provides a description of anthropometric measurements which can be used as a basis for comparison of population groups. It is intended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live.

Table of contents
  • Avant-propos
  • 1 Domaine d'application
  • 2 Références normatives
  • 3 Termes et définitions
  • 4 Conditions de prise des mesures et instruments de mesure
  • 5 Repères
  • 6 Mesures anthropométriques de base
  • Annexe A (informative) Correspondance entre les noms et numéros des dimensions dans l'ISO 7250-1 et les codes de mesures anthropométriques dans l'ISO 14738 et l'ISO
    15534
  • Bibliographie
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
What is the Redline format?
The Redline + service - standards comparator allows you to easily and simply identify major changes between the current standard and its last canceled version.

At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.
At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula

The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.

For an overview of the service, click on View a standard in redline format
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ