BEARING, BALL, AIRFRAME, ANTIFRICTION, INTERMEDIATE DUTY

FITTING, ELBOW, 45°, INTERNAL STRAIGHT THREAD PORT

Standard Practice for Manpower and Personnel

Straps, Clamps, and Mounting Hardware, Plastic and Metal for Cable Harness Tying and Support Strap, Tie Down, Adjustable, Corrosion Resistant Steel, Type VI, Class 1

AVOIDANCE OF HYDROGEN EMBRITTLEMENT OF STEEL

I/O Buffer Information Specification (IBIS) Version 4.2 / Note: Revision B*Approved 2016-10-26 SAE

Magnesium Alloy, Plate, 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5), Precipitation Heat Treated / Note: Revision B

Road Safety Applications

Process for Developing an Interoperable Cooperative Driving Use Case Test Framework and Test Procedures

On-Board System Requirements for V2V Safety Communications by Non-Light-Duty Vehicles and Motorcycles

Hose Assembly, Polytetrafluoroethylene, PTFE CRES Reinforced, 232 °C, 10 500 kPa, Beam Seal, Straight to 45°, Metric / Note: Revision A*Approved 2015-04-27 SAE

Remanufactured Hydraulic Master Cylinder for Motor Vehicle brakes Performance Requirements

Indicator, Humidity, Plug, Color Change / Note: Approved 2006-11-14 SAE

Field Test Analysis Information Report

Elevated Temperature Tensile Properties of Castings

Manual Transmission and Transaxle High-Speed Lubrication, Unbalanced and Seizure Evaluation

Wire, Electrical, Solderless Wrap, Extruded Polytetrafluoroethylene (PTFE) Insulation, Silver Coated Solid Conductor / Note: Revision A

Engine - Rocket, Solid Propellant 5 Second Duration, 4500 Pounds Thrust

Selection, Application, and Inspection of Electric Overcurrent Protective Devices / Note: Revision B

Dimensions Wheels for Demountable Rims, Demountable Rims and Spacer Bands Truck and Bus

Fitting, Elbow, 90°, Thin Wall, Flareless, Metric / Note: Revision B*Approved 2015-04-24 SAE

Sound and Thermal Insulation for Aircraft, General Specification for the installation of / Note: Revision A

Fitting End, Bulkhead, Flareless, Design Standard / Note: Revision C*Approved 2013-01-07 SAE

CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, STRAIGHT, SELF-LOCKING, SHIELD BAND TERMINATION (RFI/EMI), SHRINK SLEEVE ACCOMMODATION, CATEGORY 3B (FOR AS50151 CRIMP, MIL-DTL-26482 SERIES 2, AS81703 SERIES 3 AND MIL-DTL-83723 SERIES III CONNECTORS)

Coupling Assembly, Self-Sealing, One Side Only, Hydraulic

Magnesium Alloy Castings, 4.2Zn - 1.2 Rare Earths - 0.7Zr (ZE41A-T5), Precipitation Heat Treated

INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED CHLORINATED POLYOLEFIN, FLEXIBLE

Vehicle Lift Points for Service Garage Lifting

Steel, Corrosion-Resistant, Bars, Wire, Forgings, Extrusions, and Rings 5.0Mn - 22Cr - 12.5Ni - 2.2Mo - 0.20Cb - 0.30N - 0.20V Solution Heat Treated

Auxiliary Two-Conductor Electrical Power Connector for Truck-Trailer High-Power Jumper Cable

Insert - Thin Wall, Metric, Short and Long, Hole Preparation for

Filler Metal, Aluminum Brazing, 12Si

Nickel - Copper Alloy, Corrosion-Resistant, Bars, Forgings and Forging Stock, 67Ni - 30Cu - 0.04S, Free Machining

BEARING, ROLLER, NEEDLE, SINGLE ROW, THIN SHELL TYPE II, ANTIFRICTION, INCH

Duct Assembly, Ground, Conditioned Air, Metallic Reinforced, Low Pressure, 350°F / Note: Approved 2013-01-09 SAE

Steel, Carburizing Grade, Bars, Forgings, Mechanical Tubing and Forging Stock, Aircraft Quality, 1.2Cr - 3.2Ni - 0.12Mo (0.14 - 0.20C) (9317)

A Guide to the Reliability-Centered Maintenance (RCM) Standard / Note: Revision A

Roving, Organic Fiber (Para-Aramid), High Modulus 8520 Denier, (9500 d tex), 0.6% Finish / Note: Revision B*Approved 2014-07-31 SAE

Joint RCCC/SAE Fuel Consumption Test Procedure (Short Term In-Service Vehicle) Type I

Flight Deck Panels, Controls, and Displays / Note: Approved 2007-07-10 SAE

Fastener Part Standard - Tapping Screws and Metallic Drive Screws (Inch Dimensioned)

Alcohol, Denatured Ethyl

SPLICE, COAXIAL CABLE, ELECTRIC, PERMANENT, CRIMP AND SOLDER STYLE COPPER, INSULATED, ENVIRONMENT RESISTANT, 150 °C

WIRE, ELECTRIC, CROSSLINKED POLYALKENE INSULATED, SILVER-COATED COPPER, MEDIUM WEIGHT, 600-VOLT, 150 °C

FLANGE, MALE, BUTT WELD, TYPE I STANDARD PROFILE

BEARING, BALL, ROD END, DOUBLE ROW, PRECISION, SOLID SHANK, SELF-ALIGNING, AIRFRAME, TYPE I, -65 TO 300 °F

Coating of Fasteners Aluminum Filled, Ceramic Bonded Coating

Steel, Corrosion- and Heat-Resistant, Welding Wire 11.8Cr - 2.8Ni - 1.6Co - 1.8Mo - 0.32V

CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, SOLDER CONTACTS, AN TYPE

Carburizing and Heat Treatment of Carburizing Grade Steel Parts