Important information

To view this document, the FileOpen plug-in must be installed.
At the publisher's request, the document is available for consultation only in PDF format with single-user use and printing is not permitted. If you are not the intended user of this document, do not download it to your computer, otherwise the intended user will not be able to open it.

If you have any problems, please click here to contact customer support

If you haven't already done so, download the plug-in HERE

Consult HERE our prerequisites.

Additional informations

1.1 This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, C27400, C27450, C27451, C27453, and C28500.

1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Main informations

Collections

ASTM american standards

Publication date

April 2017

Number of pages

7 p.

Reference

ASTM B927/B927M-17

Classification index

B0927_B0927M-17

Sumary

Standard Specification for Brass Rod, Bar, and Shapes

This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, and C27400. The material shall be made from cast billets, logs, or rods of copper alloy, as determined by chemical analysis. The products shall be manufactured by such hot working, cold working, and annealing processing as to produce a uniform wrought structure. The material shall conform to the chemical compositional requirements prescribed for copper, lead, iron, and zinc. The standard tempers, either hard or soft anneal (namely: O60, H01, H02, and H04), for rod and bar are specified. Tensile requirements to which the product shall conform includes tensile strength, yield strength, and elongation. The dimensional requirements for rods, bars, and shapes are given.

Replaced standards (1)

ASTM B927/B927M-13

October 2013

Standard Cancelled

Standard Specification for Brass Rod, Bar, and Shapes

This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, and C27400. The material shall be made from cast billets, logs, or rods of copper alloy, as determined by chemical analysis. The products shall be manufactured by such hot working, cold working, and annealing processing as to produce a uniform wrought structure. The material shall conform to the chemical compositional requirements prescribed for copper, lead, iron, and zinc. The standard tempers, either hard or soft anneal (namely: O60, H01, H02, and H04), for rod and bar are specified. Tensile requirements to which the product shall conform includes tensile strength, yield strength, and elongation. The dimensional requirements for rods, bars, and shapes are given.

Standard replaced by (1)

ASTM B927/B927M-23

October 2023

Standard Current

Standard Specification for Brass Rod, Bar, and Shapes

This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, and C27400. The material shall be made from cast billets, logs, or rods of copper alloy, as determined by chemical analysis. The products shall be manufactured by such hot working, cold working, and annealing processing as to produce a uniform wrought structure. The material shall conform to the chemical compositional requirements prescribed for copper, lead, iron, and zinc. The standard tempers, either hard or soft anneal (namely: O60, H01, H02, and H04), for rod and bar are specified. Tensile requirements to which the product shall conform includes tensile strength, yield strength, and elongation. The dimensional requirements for rods, bars, and shapes are given.

What is the Redline format?

The Redline + service - standards comparator allows you to easily and simply identify major changes between the current standard and its last canceled version.

At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.

At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula

The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.

For an overview of the service, click on View a standard in redline format

Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ