ASTM F1909-98(2020)

ASTM F1909-98(2020)

January 2020
Standard Current

Standard Specification for Preformed Open–Cell Sponge Rubber Pail and Drum Gaskets

This specification covers preformed open-cell sponge rubber gaskets, for use in new or reconditioned pails or drums, of the following classes: Class A and Class B, each divided into Grade 1, Grade 2, and Grade 3. Cellular sponge rubber gaskets shall be made by incorporating a blowing agent into the compound, such as sodium bicarbonate, that gives off a gas which expands the mass during the vulcanization process, and shall be manufactured from natural rubber, synthetic rubber, or rubber-like materials, together with added compounding ingredients. Unless otherwise specified, gasket sponge rubber shall have a natural skin on both the top and bottom surfaces. Cellular rubber shall conform to the prescribed requirements as to physical properties such as (1) compression at deflection, (2) change in volume upon oil immersion, (3) change in compression value after heat aging, (4) compression set, and (5) color (tan or black). The following test methods shall be used: (1) compression deflection test, (2) oil immersion test, (3) heat oven aging test, and (4) compression set test under constant deflection. The formula for calculating the compression set is given. The requirements for sampling, test specimens and slabs, and measurements of test specimen such as width and thickness are detailed as well. The location from which standard test specimens are to be cut when testing standard test slabs or commercial flat sheets and the four-cavity frame for standard test slabs of cellular rubbers are illustrated.

See more
Important information
To view this document, the FileOpen plug-in must be installed.
At the publisher's request, the document is available for consultation only in PDF format with single-user use and printing is not permitted. If you are not the intended user of this document, do not download it to your computer, otherwise the intended user will not be able to open it.
If you have any problems, please click here to contact customer support
If you haven't already done so, download the plug-in HERE
Consult HERE our prerequisites.
Additional informations

1.1 This specification covers preformed open–cell sponge rubber gaskets of the following classes for use in new or reconditioned pails or drums.

1.1.1 Class A—Non–Oil Resistant.

1.1.2 Class B—Oil Resistant.

1.2 The values stated in SI units are to be regarded as the standard.

1.3 The following safety hazards caveat pertains only to Section 10, General Test Methods. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1: ISO Equivalency Statement—This proposed specification was found to be not equivalent.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


Main informations

Collections

ASTM american standards

Publication date

January 2020

Number of pages

5 p.

Reference

ASTM F1909-98(2020)

Classification index

F1909-98R20
Sumary
Standard Specification for Preformed Open–Cell Sponge Rubber Pail and Drum Gaskets

This specification covers preformed open-cell sponge rubber gaskets, for use in new or reconditioned pails or drums, of the following classes: Class A and Class B, each divided into Grade 1, Grade 2, and Grade 3. Cellular sponge rubber gaskets shall be made by incorporating a blowing agent into the compound, such as sodium bicarbonate, that gives off a gas which expands the mass during the vulcanization process, and shall be manufactured from natural rubber, synthetic rubber, or rubber-like materials, together with added compounding ingredients. Unless otherwise specified, gasket sponge rubber shall have a natural skin on both the top and bottom surfaces. Cellular rubber shall conform to the prescribed requirements as to physical properties such as (1) compression at deflection, (2) change in volume upon oil immersion, (3) change in compression value after heat aging, (4) compression set, and (5) color (tan or black). The following test methods shall be used: (1) compression deflection test, (2) oil immersion test, (3) heat oven aging test, and (4) compression set test under constant deflection. The formula for calculating the compression set is given. The requirements for sampling, test specimens and slabs, and measurements of test specimen such as width and thickness are detailed as well. The location from which standard test specimens are to be cut when testing standard test slabs or commercial flat sheets and the four-cavity frame for standard test slabs of cellular rubbers are illustrated.

Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ