NF EN ISO 10683

NF EN ISO 10683

September 2018
Standard Current

Fasteners - Non-electrolytically applied zinc flake coatings systems

This document specifies requirements for non-electrolytically applied zinc flake coating systems for steel fasteners. It is applicable to coatings:— with or without hexavalent chromium;— with or without top coat;— with or without lubricant (integral lubricant and/or subsequently added lubricant).It is applicable to bolts, screws, studs and nuts with ISO metric thread, to fasteners with non-ISO metric thread, and to non-threaded fasteners such as washers, pins, clips, etc.This document does not specify requirements for such fastener properties as weldability or paintability. It is not applicable to mechanically applied zinc coatings.NOTE Coatings in accordance with this document are especially used for high strength fasteners (≥ 1 000 MPa) to avoid risk of internal hydrogen embrittlement (IHE — see 4.4).Information for design and assembly of coated fasteners is given in Annex A.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

September 2018

Number of pages

40 p.

Reference

NF EN ISO 10683

ICS Codes

21.060.01   Fasteners in general
25.220.40   Metallic coatings

Classification index

E25-040

Print number

1

International kinship

ISO 10683:2018

European kinship

EN ISO 10683:2018
Sumary
Fasteners - Non-electrolytically applied zinc flake coatings systems

This document specifies requirements for non-electrolytically applied zinc flake coating systems for steel fasteners. It is applicable to coatings:

— with or without hexavalent chromium;

— with or without top coat;

— with or without lubricant (integral lubricant and/or subsequently added lubricant).

It is applicable to bolts, screws, studs and nuts with ISO metric thread, to fasteners with non-ISO metric thread, and to non-threaded fasteners such as washers, pins, clips, etc.

This document does not specify requirements for such fastener properties as weldability or paintability. It is not applicable to mechanically applied zinc coatings.

NOTE Coatings in accordance with this document are especially used for high strength fasteners (≥ 1 000 MPa) to avoid risk of internal hydrogen embrittlement (IHE — see 4.4).

Information for design and assembly of coated fasteners is given in Annex A.

Replaced standards (1)
NF EN ISO 10683
August 2014
Standard Cancelled
Fasteners - Non-electrolytically applied zinc flake coatings

ISO 10683:2014 specifies requirements for non-electrolytically applied zinc flake coatings for steel fasteners. It applies to coatings: with or without hexavalent chromium; with or without top coat; with or without lubricant (integral lubricant and/or subsequently added lubricant). It applies to bolts, screws, studs and nuts with ISO metric thread, to fasteners with non-ISO metric thread, and to non-threaded fasteners such as washers, pins, clips, etc. ISO 10683:2014 does not specify requirements for such fastener properties as weldability or paintability. It does not apply to mechanically applied zinc coatings.

Table of contents
  • Avant-propos
  • 1 Domaine d'application
  • 2 Références normatives
  • 3 Termes et définitions
  • 4 Caractéristiques générales du revêtement
  • 5 Protection contre la corrosion et essais
  • 6 Caractéristiques dimensionnelles et contrôles
  • 7 Caractéristiques mécaniques et physiques, et essais
  • 8 Application des essais
  • 9 Désignation
  • 10 Spécifications pour la commande
  • Annexe A (informative) Conception et assemblage des fixations revêtues
  • Annexe B (informative) Épaisseur de revêtement et jeu dans le filetage pour les filetages métriques ISO
  • Annexe C (informative) Systèmes de revêtement soumis à essai conformément à l'ISO 9227, BS - Évaluation de l'agressivité de l'enceinte pour l'essai au brouillard salin neutre
  • Bibliographie
What is the Redline format?
The Redline + service - standards comparator allows you to easily and simply identify major changes between the current standard and its last canceled version.

At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.
At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula

The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.

For an overview of the service, click on View a standard in redline format
New: UPSELL service
- The UPSELL service allows you to easily update one of your standards.
- With a single click, add a new language, the Requirements or Redline+ service and add one or more additional users.
- Whether you are in the process of acquiring a standard or it is already available in your personal space, the UPSELL service is available at every stage to help you understand it and implement it within your organization.
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ