NF EN ISO 11297-3

NF EN ISO 11297-3

August 2013
Standard Cancelled

Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3 : lining with close-fit pipes

ISO 11297-3:2013, in conjunction with ISO 11297-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

August 2013

Number of pages

25 p.

Reference

NF EN ISO 11297-3

ICS Codes

23.040.20   Plastics pipes
23.040.45   Plastics fittings
91.140.80   Drainage systems
93.030   External sewage systems

Classification index

P16-378-3

Print number

1 - 02/08/2013

International kinship

ISO 11297-3:2013

European kinship

EN ISO 11297-3:2013
Sumary
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3 : lining with close-fit pipes

ISO 11297-3:2013, in conjunction with ISO 11297-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.

Standard replaced by (1)
NF EN ISO 11297-3
October 2018
Standard Current
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3 : lining with close-fit pipes

This document, in conjunction with ISO 11297‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe. It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    2
  • 3.1 Généralités
    2
  • 3.2 Techniques
    2
  • 3.3 Caractéristiques
    2
  • 3.4 Matières
    2
  • 3.5 Stades des produits
    3
  • 3.6 Conditions de service
    3
  • 3.7 Assemblages
    3
  • 4 Symboles et abréviations
    4
  • 4.1 Symboles
    4
  • 4.2 Abréviations
    4
  • 5 Tuyaux au stade M
    4
  • 5.1 Matières
    4
  • 5.2 Caractéristiques générales
    5
  • 5.3 Caractéristiques des matières
    5
  • 5.4 Caractéristiques géométriques
    5
  • 5.5 Caractéristiques mécaniques
    5
  • 5.6 Caractéristiques physiques
    5
  • 5.7 Assemblage
    6
  • 5.8 Marquage
    6
  • 6 Raccords au stade M
    6
  • 7 Accessoires
    6
  • 8 Aptitude à l'emploi du système de rénovation installé au stade I
    6
  • 8.1 Matières
    6
  • 8.2 Caractéristiques générales
    6
  • 8.3 Caractéristiques des matières
    7
  • 8.4 Caractéristiques géométriques
    7
  • 8.5 Caractéristiques mécaniques
    8
  • 8.6 Caractéristiques physiques
    9
  • 8.7 Caractéristiques supplémentaires
    9
  • 8.8 Échantillonnage
    9
  • 9 Pratique d'installation
    9
  • 9.1 Travaux préparatoires
    9
  • 9.2 Stockage, manutention et transport des tuyaux et raccords
    9
  • 9.3 Équipements
    10
  • 9.4 Installation
    11
  • 9.5 Contrôle et essais relatifs au processus d'installation
    12
  • Annexe A (normative) Tuyau en polyéthylène (PE) rétabli à son état initial à chaud, plié en usine - Détermination de la capacité de mémoire
    13
  • Bibliographie
    15
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ