NF EN ISO 14554-2
Quality requirements for welding - Resistance welding of metallic materials - Part 2 : elementary quality requirements
ISO 14554-2:2013 specifies requirements for the demonstration of the capability of a manufacturer or a sub-contractor to produce welded constructions, fulfilling specified quality requirements, in one or more of the following: a) a contract between involved parties; b) an application standard; c) a regulatory requirement. The requirements contained within ISO 14554-2:2013 can be adopted in full or can be selectively deleted by the manufacturer if not applicable to the construction concerned. They provide a flexible framework for the control of welding by providing specific requirments for: 1) Case 1 ? resistance welding in contracts which require the manufacturer or sub-contractor to have a quality system other than ISO 9001[1] and where the documented welding control has a minor importance to the overall integrity of the final construction; 2) Case 2 ? resistance welding as guidance to a manufacturer or sub-contractor developing a quality system; 3) Case 3 ? references in application standards which use resistance welding as part of their requirements or in a contract between relevant parties. ISO 14554-2:2013: i) is independent of the type of welded construction to be manufactured; ii) defines quality requirements for welding both in production plants and on site; iii) provides guidance for describing the capability of a manufacturer to produce welded constructions to meet specified requirements; iv) can also be used as a basis for assessing the manufacturer in respect to his welding capability. For general guidelines for selection and use, see ISO 3834‑1, while being aware that only comprehensive and elementary requirements are specified for resistance welding. An annex gives a summary comparison of specific quality requirements for resistance welding in ISO 14554-2:2013 and ISO 14554‑1.
ISO 14554-2:2013 specifies requirements for the demonstration of the capability of a manufacturer or a sub-contractor to produce welded constructions, fulfilling specified quality requirements, in one or more of the following: a) a contract between involved parties; b) an application standard; c) a regulatory requirement.
The requirements contained within ISO 14554-2:2013 can be adopted in full or can be selectively deleted by the manufacturer if not applicable to the construction concerned. They provide a flexible framework for the control of welding by providing specific requirments for: 1) Case 1 ? resistance welding in contracts which require the manufacturer or sub-contractor to have a quality system other than ISO 9001[1] and where the documented welding control has a minor importance to the overall integrity of the final construction; 2) Case 2 ? resistance welding as guidance to a manufacturer or sub-contractor developing a quality system; 3) Case 3 ? references in application standards which use resistance welding as part of their requirements or in a contract between relevant parties.
ISO 14554-2:2013: i) is independent of the type of welded construction to be manufactured; ii) defines quality requirements for welding both in production plants and on site; iii) provides guidance for describing the capability of a manufacturer to produce welded constructions to meet specified requirements; iv) can also be used as a basis for assessing the manufacturer in respect to his welding capability.
For general guidelines for selection and use, see ISO 3834‑1, while being aware that only comprehensive and elementary requirements are specified for resistance welding. An annex gives a summary comparison of specific quality requirements for resistance welding in ISO 14554-2:2013 and ISO 14554‑1.
Le présent document s'applique dans le cas où la capacité d'un constructeur, d'un fabricant ou d'un sous-traitant à produire des structures soudées doit être démontrée.
- Avant-proposiv
-
1 Domaine d'application1
-
2 Références normatives2
-
3 Termes et définitions2
-
4 Revue de contrat et revue de conception2
-
5 Sous-traitant2
-
6 Personnel en soudage2
-
6.1 Généralités2
-
6.2 Opérateurs2
-
6.3 Régleur sur machine de soudage par résistance2
-
7 Matériel3
-
8 Activités de soudage3
-
9 Electrodes de soudage et accessoires3
-
10 Contrôles, essais et examens liés au soudage3
-
10.1 Généralités3
-
10.2 Personnel chargé des contrôles, essais et examens3
-
11 Stockage du matériau de base3
-
12 Non-conformités et actions correctives3
-
13 Enregistrements relatifs à la qualité3
- Annexe A (informative) Résumé comparatif des exigences de qualité en soudage selon la présente partie de l'ISO 14554 et l'ISO 14554-14
- Bibliographie5
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ