NF EN ISO 15011-4

NF EN ISO 15011-4

August 2006
Standard Cancelled

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 4 : fume data sheets

ISO 15011-4:2006 covers health and safety in welding and allied processes.ISO 15011-4:2006 specifies requirements for determination of the emission rate and chemical composition of welding fume in order to prepare fume data sheets..It applies to all filler materials used for joining or surfacing by arc welding using a manual, partly mechanised or fully automatic process, depositing unalloyed steel, alloyed steel and non-ferrous alloys. Manual metal arc welding, gas-shielded metal arc welding with solid wires, metal-cored and flux-cored wires and arc welding with self-shielded flux-cored wires are included within the scope of ISO 15011-4:2006.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Thematics

Gestion des risques et SST, QSE, Sécurité

Publication date

August 2006

Number of pages

33 p.

Reference

NF EN ISO 15011-4

ICS Codes

13.040.30   Workplace atmospheres
13.100   Occupational safety. Industrial hygiene
25.160.10   Welding processes

Classification index

A88-200-4

Print number

1 - 03/08/2006

International kinship

ISO 15011-4:2006

European kinship

EN ISO 15011-4:2006
Sumary
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 4 : fume data sheets

ISO 15011-4:2006 covers health and safety in welding and allied processes.

ISO 15011-4:2006 specifies requirements for determination of the emission rate and chemical composition of welding fume in order to prepare fume data sheets..

It applies to all filler materials used for joining or surfacing by arc welding using a manual, partly mechanised or fully automatic process, depositing unalloyed steel, alloyed steel and non-ferrous alloys. Manual metal arc welding, gas-shielded metal arc welding with solid wires, metal-cored and flux-cored wires and arc welding with self-shielded flux-cored wires are included within the scope of ISO 15011-4:2006.

Standard replaced by (1)
NF EN ISO 15011-4
February 2018
Standard Current
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 4 : fume data sheets

ISO 15011-4:2017 covers health and safety in welding and allied processes. It specifies requirements for determination of the emission rate and chemical composition of welding fume in order to prepare fume data sheets. ISO 15011-4:2017 applies to all filler materials used for joining or surfacing by arc welding using a manual, partly mechanized or fully automatic process, depositing unalloyed steel, alloyed steel and non‑ferrous alloys. Manual metal arc welding, gas‑shielded metal arc welding with solid wires, metal‑cored and flux‑cored wires and arc welding with self‑shielded flux‑cored wires are included within the scope of this document.

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    2
  • 4 Principe
    2
  • 5 Mode opératoire
    3
  • 6 Conditions d'essai
    3
  • 6.1 Paramètres d'essai génériques
    3
  • 6.2 Essais des électrodes pour soudage manuel à l'arc avec électrodes enrobées
    5
  • 6.3 Essais sur fil plein pour soudage à l'arc avec fil plein sous protection gazeuse et de fil fourré pour soudage à l'arc avec fil fourré sous protection gazeuse
    6
  • 6.4 Essais sur fil fourré autoprotecteur pour soudage à l'arc avec fil fourré autoprotecteur
    8
  • 7 Rapport d'essai
    9
  • 7.1 Fiches d'information sur les fumées
    9
  • 7.2 Mesures transitoires
    10
  • 7.3 Renouvellement des essais
    10
  • 7.4 Partage de données
    10
  • 7.5 Validation des fiches d'information sur les fumées
    11
  • Annexe A (normative) Fiche d'information sur les fumées
    12
  • Annexe B (informative) Partie optionnelle d'une fiche d'information sur les fumées
    14
  • Annexe C (informative) Exemples de données de performance
    15
  • Annexe D (informative) Utilisation des fiches d'information sur les fumées de soudage
    17
  • Annexe E (informative) Composants principaux et composants clés des fumées de soudage
    20
  • Annexe F (informative) Exemple de système de classification d'un produit consommable de soudage
    22
  • Annexe G (informative) Exemple de fiche d'information sur les fumées pour une électrode de soudage manuel à l'arc avec électrodes enrobées d'un acier inoxydable (y compris la partie optionnelle complémentaire)
    23
  • Bibliographie
    25
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ