NF EN ISO 15012-1

NF EN ISO 15012-1

June 2013
Standard Cancelled

Health and safety in welding and allied processes - Equipment for capture and separation of welding fume - Part 1 : requirements for testing and marking of separation efficiency

ISO 15012-1:2013 specifies a method for testing equipment for the separation of welding fume in order to determine whether its separation efficiency meets specified requirements.The method specified does not apply to testing of filter cartridges independent of the equipment in which they are intended to be used.ISO 15012-1:2013 applies to equipment that is manufactured after its publication.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Thematics

Gestion des risques et SST

Publication date

June 2013

Number of pages

26 p.

Reference

NF EN ISO 15012-1

ICS Codes

13.040.30   Workplace atmospheres
25.160.10   Welding processes

Classification index

A88-210-1

Print number

1 - 24/05/2013

International kinship

ISO 15012-1:2013

European kinship

EN ISO 15012-1:2013
Sumary
Health and safety in welding and allied processes - Equipment for capture and separation of welding fume - Part 1 : requirements for testing and marking of separation efficiency

ISO 15012-1:2013 specifies a method for testing equipment for the separation of welding fume in order to determine whether its separation efficiency meets specified requirements.

The method specified does not apply to testing of filter cartridges independent of the equipment in which they are intended to be used.

ISO 15012-1:2013 applies to equipment that is manufactured after its publication.

Replaced standards (1)
NF EN ISO 15012-1
July 2005
Standard Cancelled
Health and safety in welding and allied processes - Requirements testing and marking of equipment for air filtration - Part 1 : Testing of the separation efficiency for welding fume

ISO 15012-1:2004 deals with the significant hazards caused by the emission of welding fume particles from welding fume separation equipment operated according to its intended use and under the conditions foreseen by the manufacturer. ISO 15012-1:2004 specifies safety requirements concerning the separation of welding fumes and describes a method for determining the particle separation efficiency of welding fume separation equipment. ISO 15012-1:2004 does not deal with: hazards caused by gases emitted by welding, cutting and allied processes or by the welding fume separation equipment itself; hazards caused by the noise and vibrations of the welding fume separation equipment; other fundamental aspects of safety technology, such as electrical, mechanical and pneumatical safety, maintenance, etc.

Standard replaced by (1)
NF EN ISO 21904-2
March 2020
Standard Current
Health and safety in welding and allied processes - Equipment for capture and separation of welding fume - Part 2 : requirements for testing and marking of separation efficiency

This document specifies a method for testing equipment for the separation of welding fume in order to determine whether its separation efficiency meets specified requirements. The method specified does not apply to testing of filter cartridges independent of the equipment in which they are intended to be used. This document applies to equipment that is manufactured after its publication. NOTE General ventilation systems are excluded from the Scope of ISO 21904-1.

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    1
  • 4 Exigence
    2
  • 5 Principe
    2
  • 6 Équipement
    3
  • 7 Méthode d'essai
    6
  • 7.1 Choix du dispositif d'essai
    6
  • 7.2 Conditions d'essai
    6
  • 7.3 Mode opératoire
    6
  • 7.4 Calcul de l'efficacité de la séparation
    11
  • 8 Exactitude de mesure
    11
  • 9 Marquage
    11
  • Annexe A (normative) Étiquette pour équipement de filtration de fumées de soudage
    12
  • Annexe B (informative) Source de fumées de soudage
    13
  • Annexe C (informative) Cabine d'essai
    15
  • Bibliographie
    16
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
New: UPSELL service
- The UPSELL service allows you to easily update one of your standards.
- With a single click, add a new language, the Requirements or Redline+ service and add one or more additional users.
- Whether you are in the process of acquiring a standard or it is already available in your personal space, the UPSELL service is available at every stage to help you understand it and implement it within your organization.
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ