NF EN ISO 15614-13

June 2005

Standard Cancelled

Specification and qualificationl of welding procedures for metallic materials - Welding procedure test - Part 13 : resistance butt and flash welding

ISO 15614-13:2005 specifies the tests which should be used for qualification of welding procedure specifications.It applies to resistance butt welding and flash welding of metallic materials, e.g. with solid, tubular, flat or circular cross-section. The basic principles of ISO 15614-13:2005 may be applied to other resistance welding processes when this is specified in the specification.ISO 15614-13:2005 defines the conditions for carrying out tests and the limits of validity of a qualified welding procedure for all practical welding operations covered by ISO 15614-13:2005.ISO 15614-13:2005 covers the following resistance welding processes as defined in ISO 4063:24 flash welding using direct current or alternating current with various movement sequences, constant flashing and pulsed flashing;25 resistance butt welding, using direct current or alternating current with various pressure sequences.

View the extract

Main informations

Collections

National standards and national normative documents

Publication date

June 2005

Number of pages

26 p.

Reference

NF EN ISO 15614-13

ICS Codes

25.160.10 Welding processes

Classification index

A89-057-13

Print number

1 - 23/06/2005

International kinship

ISO 15614-13:2005

European kinship

EN ISO 15614-13:2005

Sumary

Specification and qualificationl of welding procedures for metallic materials - Welding procedure test - Part 13 : resistance butt and flash welding

ISO 15614-13:2005 specifies the tests which should be used for qualification of welding procedure specifications.

It applies to resistance butt welding and flash welding of metallic materials, e.g. with solid, tubular, flat or circular cross-section. The basic principles of ISO 15614-13:2005 may be applied to other resistance welding processes when this is specified in the specification.

ISO 15614-13:2005 defines the conditions for carrying out tests and the limits of validity of a qualified welding procedure for all practical welding operations covered by ISO 15614-13:2005.

ISO 15614-13:2005 covers the following resistance welding processes as defined in ISO 4063:

24 flash welding using direct current or alternating current with various movement sequences, constant flashing and pulsed flashing;

25 resistance butt welding, using direct current or alternating current with various pressure sequences.

Standard replaced by (1)

NF EN ISO 15614-13

August 2012

Standard Cancelled

Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13 : upset resistance butt and flash welding

ISO 15614-13:2012 specifies tests for the qualification of welding procedure specifications applicable to upset (resistance butt) welding and flash welding of metallic materials, e.g. with solid, tubular, flat or circular cross-section. Its basic principles can also be applied to other resistance welding processes when this is stated in the specification. ISO 15614-13:2012 defines the conditions for carrying out tests and the limits of validity of a qualified welding procedure for all the practical welding operations that it covers. The tests required to qualify the procedure for a particular component or assembly depend on the performance and quality requirements of the component or assembly, as defined in the design specification. The tests are intended to be carried out in accordance with the requirements of ISO 15614-13:2012, unless more severe tests are specified by the relevant application standard or specification and when these apply. ISO 15614-13:2012 covers the following resistance welding processes, as defined in ISO 4063: 24 flash welding, using direct current or alternating current with various movement sequences, constant flashing and pulsed flashing; 25 resistance upset welding, using direct current or alternating current with various pressure sequences.

Table of contents

Avant-propos
iv
Introduction
vi
1
Domaine d'application 1
2
Références normatives 2
3
Termes et définitions 3
4
Descriptif de mode opératoire de soudage préliminaire (DMOS-P) 3
5
Épreuve de qualification du mode opératoire de soudage 3
6
Assemblage de qualification et éprouvette 4
6.1 Généralités
4
6.2
Forme et dimensions des éprouvettes 4
6.3
Soudage des composants, des assemblages de qualification ou des éprouvettes 6
7
Essais et contrôle 6
7.1
Étendue du contrôle 6
7.2
Essais non destructifs 6
7.3
Essais destructifs 7
7.4
Coupe macrographique 7
7.5
Filiation de dureté 7
7.6
Contre-essais 7
8
Domaine de validité 8
8.1 Généralités
8
8.2 Fabricant
8
8.3
Métaux de base 8
8.4
Modes opératoires de soudage 8
8.5
Certificat de qualification 8
9
Procès-verbal de qualification du mode opératoire de soudage (PV-QMOS) 8
Annexe A (informative) Exemple de qualification de mode opératoire de soudage - Certificat de qualification
9
Annexe B (informative) Exemple de procès-verbal de qualification de mode opératoire de
soudage (PV-QMOS)
11

New: UPSELL service

- The UPSELL service allows you to easily update one of your standards.
- With a single click, add a new language, the Requirements or Redline+ service and add one or more additional users.
- Whether you are in the process of acquiring a standard or it is already available in your personal space, the UPSELL service is available at every stage to help you understand it and implement it within your organization.

Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ