NF EN ISO 15876-2
Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2 : Pipes
ISO 15876-2:2017 specifies the characteristics of pipes for polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 15876‑1). The designation polybutene is used together with the abbreviation PB throughout this document. ISO 15876-2:2017 covers a range of service conditions (application classes), design pressures and pipe dimension classes. For values of TD, Tmax and Tmal in excess of those in ISO 15876‑1, this document does not apply. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It also specifies the test parameters for the test methods referred to in this document. In conjunction with the other parts of ISO 15876, this document is applicable to PB pipes, their joints and to joints with components of PB, other plastics and non-plastics materials intended to be used for hot and cold water installations. It is applicable to pipes with or without (a) barrier layer(s). NOTE 2 In the case of plastics pipes provided with a thin barrier layer, e.g. to prevent or greatly diminish the diffusion of gases and the transmission of light into or through the pipe wall, the design stress requirements are totally met by the base polymer (PB).
ISO 15876-2:2017 specifies the characteristics of pipes for polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 15876‑1).
The designation polybutene is used together with the abbreviation PB throughout this document.
ISO 15876-2:2017 covers a range of service conditions (application classes), design pressures and pipe dimension classes. For values of TD, Tmax and Tmal in excess of those in ISO 15876‑1, this document does not apply.
NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with the other parts of ISO 15876, this document is applicable to PB pipes, their joints and to joints with components of PB, other plastics and non-plastics materials intended to be used for hot and cold water installations.
It is applicable to pipes with or without (a) barrier layer(s).
NOTE 2 In the case of plastics pipes provided with a thin barrier layer, e.g. to prevent or greatly diminish the diffusion of gases and the transmission of light into or through the pipe wall, the design stress requirements are totally met by the base polymer (PB).
<p>ISO 15876-2:2003 specifies the characteristics of pipes made from polybutylene (PB) for piping systems intended to be used for hot and cold water installations, within buildings, for the conveyance of water which may or may not be intended for human consumption (domestic systems) or for heating systems, under operating pressures and temperatures appropriate to the class of application.</p> <p>It covers a range of service conditions (application classes), design pressures and pipe dimension classes. It does not apply if the values of the design temperature, maximum design temperature and malfunction temperature are in excess of those given in ISO 15876-1.</p> <p>It also specifies the test parameters for the test methods referred to in the standard.</p> <p>In conjunction with the other parts of ISO 15876, it is applicable to PB pipes and their joints, including joints with other PB components and components made of other plastics and non-plastics materials intended to be used for hot and cold water installations.</p> <p>It is applicable to pipes with or without (a) barrier layer(s).</p>
Le présent amendement à la NF EN ISO 15876-2:2004 clarifie les exigences en matière de dimensions et de tolérances pour les canalisations avec couche barrière et établit un mode opératoire commun expliquant comment concevoir et tester ces tubes.
-
1 Domaine d'application
-
2 Références normatives
-
3 Termes et définitions, symboles et abréviations
-
4 Matière des tubes
-
5 Caractéristiques générales
-
6 Caractéristiques géométriques
-
7 Caractéristiques mécaniques
-
8 Caractéristiques physiques et chimiques
-
9 Exigences de performance
-
10 Marquage
- Annexe A Détermination de S calc,max
- Bibliographie
The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.
The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.
With Requirements, quickly access the main part of the normative text!
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ