NF EN ISO 16810

NF EN ISO 16810

May 2014
Standard Cancelled

Non-destructive testing - Ultrasonic testing - General principles

ISO 16810:2012 defines the general principles required for the ultra­sonic examination of industrial products that permit the trans­mis­sion of ultrasound.The specific conditions of application and use of ultrasonic examination, which depend on the type of product examined, are described in documents which could include: a) product standards; b) specifications; c) codes; d) contractual documents; e) written procedures.Unless otherwise specified in the referencing documents the minimum requirements of ISO 16810:2012 are applicable. ISO 16810:2012 does not define: 1) extent of examination and scanning plans; 2) acceptance criteria.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

May 2014

Number of pages

18 p.

Reference

NF EN ISO 16810

ICS Codes

19.100   Non-destructive testing

Classification index

A09-332

Print number

1

International kinship

ISO 16810:2012

European kinship

EN ISO 16810:2014
Sumary
Non-destructive testing - Ultrasonic testing - General principles

ISO 16810:2012 defines the general principles required for the ultra­sonic examination of industrial products that permit the trans­mis­sion of ultrasound.

The specific conditions of application and use of ultrasonic examination, which depend on the type of product examined, are described in documents which could include: a) product standards; b) specifications; c) codes; d) contractual documents; e) written procedures.

Unless otherwise specified in the referencing documents the minimum requirements of ISO 16810:2012 are applicable.

ISO 16810:2012 does not define: 1) extent of examination and scanning plans; 2) acceptance criteria.

Replaced standards (2)
NF EN 583-1
July 1999
Standard Cancelled
Non-destructive testing. Ultrasonic examination. Part 1 : general principles.

Le présent document décrit les principes généraux du contrôle par ultrasons des produits industriels (techniques utilisées, caractéristiques générales de l'appareillage, réglages, préparation du contrôle et contrôle).

NF EN 583-1/A1
July 2004
Standard Cancelled
Non-destructive testing - Ultrasonic examination - Part 1 : general principles

Le présent document décrit les principes généraux du contrôle par ultrasons des produits industriels (techniques utilisées, caractéristiques générales de l'appareillage, réglages, préparation du contrôle et contrôle).

Standard replaced by (1)
NF EN ISO 16810
October 2024
Standard Current
Non-destructive testing - Ultrasonic testing - General principles

This document specifies the general principles for the ultrasonic testing of industrial products that permit the transmission of ultrasound. The specific conditions of application and use of ultrasonic testing, which depend on the type of product to be tested, are described in documents which can include: —     product standards; —     specifications; —     codes; —     contractual documents; —     written procedures. This document specifies the minimum applicable requirements, unless otherwise specified in the referencing documents. This document does not specify: —     extent of testing and scan plans; —     acceptance criteria. This document describes only conventional probes, however, the general principles for ultrasonic testing also apply to ultrasonic testing using array techniques. If array techniques are used, then additional steps or verifications can be needed.

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Qualification et certification du personnel
    2
  • 4 Informations nécessaires avant le contrôle
    2
  • 5 Principes du contrôle ultrasonore
    2
  • 6 Appareillage
    3
  • 7 Réglages
    6
  • 8 Préparation pour contrôle
    7
  • 9 Contrôle
    7
  • 10 Caractérisation des discontinuités
    8
  • 11 Procédure de contrôle
    9
  • 12 Rapport d'essai
    9
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ