NF EN ISO 2063-2

NF EN ISO 2063-2

October 2017
Standard Current

Thermal spraying - Zinc, aluminium and their alloys - Part 2 : execution of corrosion protection systems

ISO 2063-2:2017 specifies requirements for corrosion protection of steel structures, components or parts, which are coated by thermal spraying of zinc, aluminium or their alloys.ISO 2063-2:2017 specifies requirements for coating manufacturers of surface preparation, thermal spraying, testing and post treatments, e.g. sealing of the coating. ISO 2063-2:2017 applies to metallic corrosion protection coatings in the case of new fabrication in the workshop, as well as on-site and for repair on-site after assembly.Requirements for coating thickness, minimum adhesive strength and surface conditions, specified in a coating specification, are given.Recommendations are given for suitable process steps and quality assurance measures for new production and maintenance and for supervising of corrosion protection works.ISO 2063-2:2017 covers the application of thermal-sprayed zinc, aluminium and their alloys for protection against corrosion in the temperature range between ?50 °C to +200 °C. Heat-resistant protective coatings of aluminium are covered by ISO 17834 and are not in the scope of ISO 2063-2:2017.ISO 2063-2:2017 specifies requirements for the equipment, the working place and the qualification of the spray and testing personnel.NOTE ISO 2063‑1:2017 is addressed to the designer and to the planning engineer of corrosion protection system.

See more
View the extract New: UPSELL service
Main informations

Collections

National standards and national normative documents

Publication date

October 2017

Number of pages

51 p.

Reference

NF EN ISO 2063-2

ICS Codes

25.220.20   Surface treatment
25.220.40   Metallic coatings

Classification index

A91-201-2

Print number

1

International kinship

ISO 2063-2:2017

European kinship

EN ISO 2063-2:2017
Sumary
Thermal spraying - Zinc, aluminium and their alloys - Part 2 : execution of corrosion protection systems

ISO 2063-2:2017 specifies requirements for corrosion protection of steel structures, components or parts, which are coated by thermal spraying of zinc, aluminium or their alloys.

ISO 2063-2:2017 specifies requirements for coating manufacturers of surface preparation, thermal spraying, testing and post treatments, e.g. sealing of the coating. ISO 2063-2:2017 applies to metallic corrosion protection coatings in the case of new fabrication in the workshop, as well as on-site and for repair on-site after assembly.

Requirements for coating thickness, minimum adhesive strength and surface conditions, specified in a coating specification, are given.

Recommendations are given for suitable process steps and quality assurance measures for new production and maintenance and for supervising of corrosion protection works.

ISO 2063-2:2017 covers the application of thermal-sprayed zinc, aluminium and their alloys for protection against corrosion in the temperature range between ?50 °C to +200 °C. Heat-resistant protective coatings of aluminium are covered by ISO 17834 and are not in the scope of ISO 2063-2:2017.

ISO 2063-2:2017 specifies requirements for the equipment, the working place and the qualification of the spray and testing personnel.

NOTE ISO 2063‑1:2017 is addressed to the designer and to the planning engineer of corrosion protection system.

Replaced standards (1)
NF EN ISO 2063
May 2005
Standard Cancelled
Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys

ISO 2063:2005 applies to thermal-sprayed metallic coatings for the protection of iron and steel against corrosion by applying zinc or aluminium or their alloys to uncoated surfaces to be protected. This International Standard deals with characteristic properties and gives test methods for coatings obtained by the spraying of zinc and aluminium and their alloys for the general purpose of corrosion protection. It gives firstly the definition, classification and symbols for these coatings in relation to their thickness. It then deals with the preparation of surfaces, application of coatings and their characteristic properties: namely, thickness, appearance and adhesion. Finally ISO 2063:2005 gives test methods for checking these properties.

ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
New: UPSELL service
- The UPSELL service allows you to easily update one of your standards.
- With a single click, add a new language, the Requirements or Redline+ service and add one or more additional users.
- Whether you are in the process of acquiring a standard or it is already available in your personal space, the UPSELL service is available at every stage to help you understand it and implement it within your organization.
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ