NF EN ISO 21268-4

NF EN ISO 21268-4

December 2019
Standard Current

Soil quality - Leaching procedures for subsequent chemical and ecotoxicological testing of soil and soil-like materials - Part 4 : influence of pH on leaching with initial acid/base addition

This document specifies a test to obtain information on the short- and long-term leaching behaviour and characteristic properties of materials.The document has been developed to measure the pH-dependent release of inorganic and organic substances from soil and soil-like material as well as to produce eluates for subsequent ecotoxicological testing. For ecotoxicological testing, see ISO 15799 and ISO 17616. The equilibrium condition, as defined in this document, is established by the addition of predetermined amounts of acid or base to reach desired final pH values.NOTE 1 Volatile organic substances include the low molecular weight substances in mixtures such as mineral oil.NOTE 2 It is not always possible to optimize test conditions simultaneously for inorganic and organic substances and optimum test conditions can also vary between different groups of organic substances. Test requirements for organic substances are generally more stringent than those for inorganic substances. The test conditions suitable for measuring the release of organic substances will generally also be applicable to inorganic substances.NOTE 3 Within the category of organic substances, a significant difference in behaviour exists between the more polar, relatively water-soluble compounds and apolar, hydrophobic organic substances (HOCs). In the latter case, mechanisms of release (e.g. particle-bound or dissolved organic carbon-bound) can be more crucial as well as sorption losses of soluble HOCs on different materials with which they come in contact (e.g. bottles, filters). The test and the results should be used for leaching of organic substances only with thorough consideration of the specific properties of the substances in question and the associated potential problems.NOTE 4 For ecotoxicological testing, eluates representing the release of both inorganic and organic substances are needed. In this document, ecotoxicological testing is meant to include genotoxicological testing.The test method produces eluates, which can subsequently be characterized by physical, chemical and ecotoxicological methods in accordance with existing standard methods. The test is not suitable for substances that are volatile under ambient conditions.For the purposes of ecotoxicological tests, the relevant pH range (see 8.2) will usually be pH 5 to pH 9.This test is mainly aimed at being used for routine and control purposes, and it cannot be used alone to describe all leaching properties of a soil. Additional leaching tests are needed for that extended goal. This document does not address issues related to health and safety. It only determines the leaching properties outlined in Clause 5.

View the extract
Main informations

Collections

National standards and national normative documents

Publication date

December 2019

Number of pages

40 p.

Reference

NF EN ISO 21268-4

ICS Codes

13.080.05   Examination of soils in general

Classification index

X31-607-4

Print number

1

International kinship

ISO 21268-4:2019

European kinship

EN ISO 21268-4:2019
Sumary
Soil quality - Leaching procedures for subsequent chemical and ecotoxicological testing of soil and soil-like materials - Part 4 : influence of pH on leaching with initial acid/base addition

This document specifies a test to obtain information on the short- and long-term leaching behaviour and characteristic properties of materials.

The document has been developed to measure the pH-dependent release of inorganic and organic substances from soil and soil-like material as well as to produce eluates for subsequent ecotoxicological testing. For ecotoxicological testing, see ISO 15799 and ISO 17616. The equilibrium condition, as defined in this document, is established by the addition of predetermined amounts of acid or base to reach desired final pH values.

NOTE 1 Volatile organic substances include the low molecular weight substances in mixtures such as mineral oil.

NOTE 2 It is not always possible to optimize test conditions simultaneously for inorganic and organic substances and optimum test conditions can also vary between different groups of organic substances. Test requirements for organic substances are generally more stringent than those for inorganic substances. The test conditions suitable for measuring the release of organic substances will generally also be applicable to inorganic substances.

NOTE 3 Within the category of organic substances, a significant difference in behaviour exists between the more polar, relatively water-soluble compounds and apolar, hydrophobic organic substances (HOCs). In the latter case, mechanisms of release (e.g. particle-bound or dissolved organic carbon-bound) can be more crucial as well as sorption losses of soluble HOCs on different materials with which they come in contact (e.g. bottles, filters). The test and the results should be used for leaching of organic substances only with thorough consideration of the specific properties of the substances in question and the associated potential problems.

NOTE 4 For ecotoxicological testing, eluates representing the release of both inorganic and organic substances are needed. In this document, ecotoxicological testing is meant to include genotoxicological testing.

The test method produces eluates, which can subsequently be characterized by physical, chemical and ecotoxicological methods in accordance with existing standard methods. The test is not suitable for substances that are volatile under ambient conditions.

For the purposes of ecotoxicological tests, the relevant pH range (see 8.2) will usually be pH 5 to pH 9.

This test is mainly aimed at being used for routine and control purposes, and it cannot be used alone to describe all leaching properties of a soil. Additional leaching tests are needed for that extended goal. This document does not address issues related to health and safety. It only determines the leaching properties outlined in Clause 5.

Replaced standards (1)
XP CEN ISO/TS 21268-4
December 2009
Standard Cancelled
Soil quality - Leaching procedures for subsequent chemical and ecotoxicological testing of soil and soil materials - Part 4 : influence of pH on leaching with initial acid/base addition

ISO/TS 21268-4:2007 specifies a test method to obtain information on the short- and long-term leaching behaviour and characteristic properties of materials. It applies to the determination of the influence of pH on the leachability of inorganic and organic constituents from soil and soil material, and the ecotoxicological effects of eluates with respect to microorganisms, fauna and flora. The test is not suitable for constituents that are volatile under ambient conditions. The test procedure specified in ISO/TS 21268-4:2007 produces eluates that are subsequently characterized by physical, chemical and ecotoxicological standard methods.

Table of contents
  • Avant-propos
  • 1 Domaine d'application
  • 2 Références normatives
  • 3 Termes et définitions
  • 4 Principe
  • 5 Réactifs
  • 6 Appareillage
  • 7 Prétraitement des échantillons
  • 9 Calculs
  • 10 Rapport d'essai
  • 11 Dosage analytique
  • 12 Caractéristiques de performance
  • Annexe A (informative) Exemple de mode opératoire de séparation liquide-solide spécifique des échantillons de sol
  • Annexe B (informative) Mise en oeuvre et utilisations de l'essai - Influence du pH sur le comportement à la lixiviation
  • Annexe C (informative) Détermination préliminaire de la consommation d'acide/de base
  • Annexe D (informative) Données de répétabilité et de reproductibilité
  • Annexe E (informative) Calcul de la durée de centrifugation en fonction de la vitesse de centrifugation et des dimensions du rotor
  • Bibliographie
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
What is the Redline format?
The Redline + service - standards comparator allows you to easily and simply identify major changes between the current standard and its last canceled version.

At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.
At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula

The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.

For an overview of the service, click on View a standard in redline format
New: UPSELL service
- The UPSELL service allows you to easily update one of your standards.
- With a single click, add a new language, the Requirements or Redline+ service and add one or more additional users.
- Whether you are in the process of acquiring a standard or it is already available in your personal space, the UPSELL service is available at every stage to help you understand it and implement it within your organization.
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ