1.1 ISO 2580-1:2002 establishes a system of designation for acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials, which may be used as the basis for specifications. 1.2 The types of ABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties Vicat softening temperaturemelt volume-flow rateCharpy notched impact strengthtensile modulus and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. 1.3 This part of ISO 2580 is applicable to all acrylonitrile-butadiene-styrene materials consisting of a continuous phase based mainly on copolymers of styrene (and/or alkyl-substituted styrene) and acrylonitrile and a dispersed elastomeric phase based mainly on polybutadiene, plus other components, in such quantities as specified in the text. It applies to ABS materials ready for normal use in the form of powder, granules, pellets or chips, unmodified or modified by colorants, additives, fillers, etc. This part of ISO 2580 does not apply to materials with a Charpy notched impact strength of less than 3 kilojoules per square metre; containing less than 50 % by mass of butadiene in the elastomer of the elastomeric phase; containing less than 15 % by mass of acrylonitrile in the continuous phase.
1.1 ISO 2580-1:2002 establishes a system of designation for acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials, which may be used as the basis for specifications.
1.2 The types of ABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties
and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.
1.3 This part of ISO 2580 is applicable to all acrylonitrile-butadiene-styrene materials consisting of a continuous phase based mainly on copolymers of styrene (and/or alkyl-substituted styrene) and acrylonitrile and a dispersed elastomeric phase based mainly on polybutadiene, plus other components, in such quantities as specified in the text.
It applies to ABS materials ready for normal use in the form of powder, granules, pellets or chips, unmodified or modified by colorants, additives, fillers, etc.
This part of ISO 2580 does not apply to materials
Le présent document établit un système de désignation des matériaux thermoplastiques acrylonitrile/butadiène, qui peut être utilisé comme base de spécifications.
<p>ISO 19062-1:2015 establishes a system of designation for acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials, which may be used as the basis for specifications.</p> <p>The types of ABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties:</p> <p>a) Vicat softening temperature;</p> <p>b) melt mass-flow rate;</p> <p>c) Charpy notched impact strength;</p> <p>d) tensile modulus;</p> <p>and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.</p> <p>ISO 19062-1:2015 is applicable to all acrylonitrile-butadiene-styrene materials consisting of a continuous phase based mainly on copolymers of styrene (and/or alkyl-substituted styrene) and acrylonitrile and a dispersed elastomeric phase based mainly on polybutadiene, plus other components, in such quantities as specified in the text.</p> <p>It applies to ABS materials ready for normal use in the form of powder, granules, pellets or chips, unmodified or modified by colorants, additives, fillers, etc.</p> <p>ISO 19062-1:2015 does not apply to materials</p> <p>a) with a Charpy notched impact strength of less than three kilojoules per square metre,</p> <p>b) containing less than 50 % by mass of butadiene in the elastomer of the elastomeric phase, and</p> <p>c) containing less than 15 % by mass of acrylonitrile in the continuous phase.</p> <p>It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 19062 does not provide engineering data, performance data, or data on processing conditions which may be required to specify a material for a particular application and/or method of processing.</p> <p>If such additional properties are required, they will be determined in accordance with the test methods specified in ISO 2580‑2, if suitable.</p> <p>In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1).</p>
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ