NF EN ISO 6789

NF EN ISO 6789

September 2003
Standard Cancelled

Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure

ISO 6789:2003 specifies the requirements for, and describes the test methods and marking of, hand torque tools used for controlled tightening of bolted connections.It applies in particular to indicating and setting torque wrenches in accordance with numbers 258 and 259 of ISO 1703:1983.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

September 2003

Number of pages

23 p.

Reference

NF EN ISO 6789

ICS Codes

25.140.30   Hand-operated tools

Classification index

E74-325

Print number

1 - 18/02/2004

International kinship

ISO 6789:2003

European kinship

EN ISO 6789:2003
Sumary
Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure

ISO 6789:2003 specifies the requirements for, and describes the test methods and marking of, hand torque tools used for controlled tightening of bolted connections.

It applies in particular to indicating and setting torque wrenches in accordance with numbers 258 and 259 of ISO 1703:1983.

Replaced standards (1)
NF EN 26789
July 1994
Standard Cancelled
Assembly tools for screws and nuts. Hand torque tools. Requirements and test methods.

Standard replaced by (2)
NF EN ISO 6789-1
May 2017
Standard Current
Assembly tools for screws and nuts - Hand torque tools -Part 1 : Requirements and methods for design conformance testing and quality conformance testing : minimum requirements for declaration of conformance

ISO 6789-1:2017 specifies the conformance testing and marking requirements for hand torque tools used for controlled tightening of screws and nuts. It also specifies the minimum requirements for declaration of conformance for hand torque tools. ISO 6789-1:2017 applies to hand torque tools which are classified as indicating torque tools (Type I) and setting torque tools (Type II). NOTE Hand torque tools covered by this document are those identified in ISO 1703:2005 by reference numbers 6 1 00 11 0, 6 1 00 11 1 and 6 1 00 12 0, 6 1 00 12 1 and 6 1 00 14 0, 6 1 00 15 0. ISO 1703 is currently under revision. In the next edition, torque tools will be moved to an own clause, and with this change the reference numbers will also change and additional reference numbers will be added. ISO 6789-1:2017 does not specify requirements of calibration certificates for hand torque tools. These are described in ISO 6789‑2.

NF EN ISO 6789-2
May 2017
Standard Current
Assembly tools for screws and nuts - Hand torque tools - Part 2 : Requirements for calibration and determination of measurement uncertainly

ISO 6789-2:2017 specifies the method for the calibration of hand torque tools and describes the method of calculation of measurement uncertainties for the calibration. ISO 6789-2:2017 specifies the minimum requirements for the calibration of the torque measurement device where the relative measurement uncertainty interval, W´md, is not already provided by a traceable calibration certificate. ISO 6789 is applicable for the step by step (static) and continuous (quasi-static) calibration of torque measurement devices, the torque of which is defined by measuring of the elastic form change of a deformable body or a measured variable which is in proportion to the torque. ISO 6789-2:2017 applies to hand torque tools which are classified as indicating torque tools (Type I) and setting torque tools (Type II). NOTE Hand torque tools covered by this document are the ones identified in ISO 1703:2005 by reference numbers 6 1 00 11 0, 6 1 00 11 1 and 6 1 00 12 0, 6 1 00 12 1 and 6 1 00 14 0, 6 1 00 15 0. ISO 1703 is currently under revision. In the next edition, torque tools will be moved to an own clause, and with this change the reference numbers will also change and additional reference numbers will be added.

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    1
  • 4 Classification
    2
  • 5 Exigences
    3
  • 5.1 Contrôle de conformité de conception
    3
  • 5.2 Contrôle de conformité de qualité
    5
  • 5.3 Réétalonnage 5
  • 6 Étalonnage 5
  • 6.1 Dispositif d'étalonnage
    5
  • 6.2 Température d'étalonnage
    6
  • 6.3 Conditions d'étalonnage
    6
  • 6.4 Procédure d'étalonnage
    S
  • 6.5 Exemples d'étalonnage
    S
  • 7 Marquage
    11
  • Annexe A (normative) Outils dynamométriques à lecture directe: Type I
    12
  • Annexe B (normative) Outils dynamométriques à déclenchement: Type II
    13
  • Bibliographie
    15
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ