NF ISO 12917-1

NF ISO 12917-1

November 2002
Standard Cancelled

Petroleum and liquid petroleum products - Calibration of horizontal cylindrical tanks - Part 1 : manual methods

ISO 12917-1 specifies manual methods for the calibration of nominally horizontal cylindrical tanks, installed at a fixed location. It is applicable to horizontal tanks up to 4 m in diameter and 30 m in length.The methods are applicable to insulated and non-insulated tanks, either when they are above-ground or underground. The methods are applicable to pressurized tanks, and to both knuckle-dish-end and flat-end cylindrical tanks as well as elliptical and spherical head tanks.ISO 12917-1 is applicable to tanks inclined by up to 10 % from the horizontal, provided a correction is applied for the measured tilt

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

November 2002

Number of pages

26 p.

Reference

NF ISO 12917-1

ICS Codes

75.180.30   Volumetric equipment and measurements

Classification index

M08-024-1

Print number

1 - 07/12/2002

International kinship

ISO 12917-1:2002
Sumary
Petroleum and liquid petroleum products - Calibration of horizontal cylindrical tanks - Part 1 : manual methods

ISO 12917-1 specifies manual methods for the calibration of nominally horizontal cylindrical tanks, installed at a fixed location. It is applicable to horizontal tanks up to 4 m in diameter and 30 m in length.

The methods are applicable to insulated and non-insulated tanks, either when they are above-ground or underground. The methods are applicable to pressurized tanks, and to both knuckle-dish-end and flat-end cylindrical tanks as well as elliptical and spherical head tanks.

ISO 12917-1 is applicable to tanks inclined by up to 10 % from the horizontal, provided a correction is applied for the measured tilt

Standard replaced by (1)
NF ISO 12917-1
August 2019
Standard Current
Petroleum and liquid petroleum products - Calibration of horizontal cylindrical tanks - Part 1 : manual methods

ISO 12917-1:2017 specifies manual methods for the calibration of nominally horizontal cylindrical tanks, installed at fixed locations. The methods in this document are applicable to insulated and non-insulated tanks, either when they are above-ground or underground. The methods are applicable to pressurized tanks and to both knuckle-dish-end and flat-end cylindrical tanks as well as elliptical and spherical head tanks. ISO 12917-1:2017 is applicable to tanks inclined from the horizontal, provided a correction is applied for the measured tilt. Although this document does not impose any limits on the maximum tank diameter and maximum tank tilt to which this document is applicable, the practical limits would be about 4 m in diameter and 10° in tilt.

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    1
  • 4 Précautions
    2
  • 4.1 Généralités
    2
  • 4.2 Méthode interne
    2
  • 4.3 Méthode externe
    2
  • 5 Équipement
    2
  • 5.1 Équipement tel qu'utilisé dans la série ISO 7507
    2
  • 5.2 Perche télescopique
    2
  • 6 Exigences générales
    2
  • 7 Procédures de jaugeage
    3
  • 8 Mesurages externes
    3
  • 8.1 Introduction
    3
  • 8.2 Généralités
    3
  • 8.3 Répétition des mesurages
    4
  • 8.4 Tolérances
    4
  • 8.5 Autres mesurages sur les tôles de la robe du réservoir
    4
  • 9 Mesurages internes
    5
  • 9.1 Généralités
    5
  • 9.2 Répétition des mesurages
    5
  • 9.3 Tolérances
    5
  • 9.4 Autres mesurages sur les tôles de la robe du réservoir
    5
  • 10 Mesurages auxiliaires
    6
  • 10.1 Corps étrangers
    6
  • 10.2 Mesurage de l'inclinaison
    6
  • 11 Autres paramètres
    7
  • 12 Rejaugeage
    7
  • 13 Données descriptives
    7
  • 14 Calcul des barèmes des réservoirs - Règles générales
    8
  • 15 Effets de l'inclinaison
    8
  • 16 Calculs systématiques (résumé)
    8
  • 16.1 Généralités
    8
  • 16.2 Volume du cylindre
    8
  • 16.3 Volume des fonds en anse de panier
    9
  • 16.4 Fonds elliptiques
    11
  • 16.5 Fonds sphériques
    12
  • 16.6 Corps étrangers
    12
  • Annexe A (normative) Inclinaison
    13
  • Annexe B (informative) Corrections de volume dans le barème de jaugeage
    15
  • Bibliographie
    18
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ