FD CEN ISO/TS 15694

FD CEN ISO/TS 15694

June 2004
Published document Current

Mechanical vibration and shock - Measurement and evaluation of single shocks transmitted from hand-held and hand-guided machines to the hand-arm system

ISO/TS 15694:2004 specifies methods for measuring single shocks at the handle(s) of hand-held and hand-guided machinery characterized by a maximum strike rate below 5 Hz. ISO/TS 15694:2004 also defines additional requirements for the measuring instrumentation which is necessary for the evaluation of shocks. The aim is to facilitate the gathering of emission and human exposure data in order to provide a basis for emission declaration and for the future development of exposure risk criteria. However, ISO/TS 15694:2004 does not provide methods for the interpretation of the potential human effects of single shocks. It is therefore a basis for measurement and evaluation of emission of single shocks from hand-held and hand-guided machinery but does not cover the evaluation of human exposure.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Thematics

Gestion des risques et SST, QSE, Sécurité

Publication date

June 2004

Number of pages

23 p.

Reference

FD CEN ISO/TS 15694

ICS Codes

13.160   Vibration and shock with respect to human beings
17.160   Vibrations, shock and vibration measurements

Classification index

E90-694

Print number

1 - 16/06/2004

International kinship

ISO/TS 15694:2004

European kinship

CEN ISO/TS 15694:2004
Sumary
Mechanical vibration and shock - Measurement and evaluation of single shocks transmitted from hand-held and hand-guided machines to the hand-arm system

ISO/TS 15694:2004 specifies methods for measuring single shocks at the handle(s) of hand-held and hand-guided machinery characterized by a maximum strike rate below 5 Hz.

ISO/TS 15694:2004 also defines additional requirements for the measuring instrumentation which is necessary for the evaluation of shocks.

The aim is to facilitate the gathering of emission and human exposure data in order to provide a basis for emission declaration and for the future development of exposure risk criteria. However, ISO/TS 15694:2004 does not provide methods for the interpretation of the potential human effects of single shocks.

It is therefore a basis for measurement and evaluation of emission of single shocks from hand-held and hand-guided machinery but does not cover the evaluation of human exposure.

Table of contents
View the extract
  • Avant-propos
    3
  • Introduction
    4
  • 1 Domaine d'application
    4
  • 2 Références normatives
    4
  • 3 Termes et définitions
    5
  • 4 Paramètres de description des chocs simples
    5
  • 4.1 Accélération
    5
  • 4.2 Accélération pondérée flat h
    6
  • 4.3 Valeur efficace (RMS) de l'accélération pondérée flat h
    6
  • 4.4 Valeur efficace mobile (RRMS) de l'accélération pondérée flatte
    6
  • 4.5 Valeur de la racine quatrième (RMQ) de l'accélération pondérée flatte
    7
  • 4.6 Maximum de la vibration transitoire de l'accélération pondérée flatte
    7
  • 4.7 Valeur de crête de l'accélération pondérée flat h
    7
  • 4.8 Facteur de crête de l'accélération pondérée flat h
    7
  • 4.9 Quotient de contenu de choc de l'accélération pondérée flat h
    8
  • 4.10 Accélération pondérée W h
    8
  • 4.11 Valeur efficace de l'accélération pondérée W h
    8
  • 4.12 Valeur de la racine quatrième de l'accélération pondérée W h
    8
  • 4.13 Quotient de contenu de choc de l'accélération pondérée W h
    9
  • 5 Appareillage de mesure
    9
  • 6 Procédure de mesurage
    9
  • 6.1 Fixation des accéléromètres
    9
  • 6.2 Orientation des accéléromètres
    9
  • 6.3 Procédure de travail
    10
  • 7 Rapport de mesurage
    10
  • Annexe A (normative) Spécifications et méthodes d'essai pour l'appareillage de mesure
    11
  • A.1
    Généralités 11
  • A.2
    Réponse phase-fréquence 11
  • A.3
    Réponse amplitude-fréquence 13
  • Annexe B (informative) Recommandations et méthodes d'essai pour un appareillage de mesure numérique
    14
  • B.1
    Généralités 14
  • B.2
    Réponse phase-fréquence 14
  • Annexe C (informative) Autre paramètre de description des chocs simples
    16
  • Annexe D (normative) Filtre de pondération fréquentielle flat h
    17
  • Annexe E (normative) Filtre de pondération fréquentielle Wh de l'EN ISO 5349-1
    19
  • Bibliographie
    21
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ