NF EN ISO 28927-1
Hand-held portable power tools - Test method for evaluation of vibration emission - Part 1 : angle and vertical grinders
ISO 28927-1:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven angle and vertical grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with a specified test wheel and run under no‑load conditions. The method has been established for surface grinding tasks only (cutting and sanding generally create lower vibrations). It is intended that the results be used to compare different models of the same type of machine. ISO 28927-1:2009 is applicable to hand-held machines, driven pneumatically or by other means, intended for grinding, cutting-off and rough sanding, with bonded, coated and super-abrasive products for use on all kinds of materials. It is not applicable to grinders used with wire brushes or to die or straight grinders.
ISO 28927-1:2009 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven angle and vertical grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with a specified test wheel and run under no‑load conditions. The method has been established for surface grinding tasks only (cutting and sanding generally create lower vibrations). It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-1:2009 is applicable to hand-held machines, driven pneumatically or by other means, intended for grinding, cutting-off and rough sanding, with bonded, coated and super-abrasive products for use on all kinds of materials. It is not applicable to grinders used with wire brushes or to die or straight grinders.
<p>This document specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven angle and vertical grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with a specified test wheel and run under no‑load conditions. The method has been established for surface grinding tasks only. Cutting and sanding generally create lower vibrations. It is intended that the results be used to compare different models of the same type of machine.</p> <p>This document is applicable to hand-held machines (see Clause 5), driven pneumatically or by other means, intended for grinding, cutting-off and rough sanding, with bonded, coated and super-abrasive products and with wire brushes for use on all kinds of materials. It is not applicable to die grinders or straight grinders.</p> <p>NOTE To avoid confusion with the terms "power tool" and "inserted tool", <i>machine</i> is used for the former throughout this document.</p>
- Avant-proposiv
- Introductionvi
-
1 Domaine d'application1
-
2 Références normatives1
-
3 Termes, définitions et symboles2
-
3.1 Termes et définitions2
-
3.2 Symboles2
-
4 Normes de référence et codes d'essai de vibration3
-
5 Description de la famille de machines3
-
6 Caractérisation des vibrations5
-
6.1 Direction du mesurage5
-
6.2 Emplacement des mesurages5
-
6.3 Amplitude des vibrations8
-
6.4 Combinaison des directions de vibrations8
-
7 Exigences pour l'appareillage8
-
7.1 Généralités8
-
7.2 Montage des transducteurs8
-
7.3 Filtre de pondération fréquentielle9
-
7.4 Durée d'intégration9
-
7.5 Équipement auxiliaire9
-
7.6 Étalonnage9
-
8 Conditions d'essai et de fonctionnement de la machine9
-
8.1 Généralités9
-
8.2 Conditions de fonctionnement10
-
8.3 Autres valeurs à spécifier10
-
8.4 Équipement accessoire, pièce et tâche11
-
8.5 Opérateur14
-
9 Mode opératoire de mesure et validation14
-
9.1 Valeurs de vibration consignées14
-
9.2 Déclaration et vérification des valeurs d'émission vibratoire15
-
10 Rapport d'essai15
- Annexe A (informative) Modèle de rapport d'essai pour les émissions de vibrations des meuleuses verticales et les meuleuses d'angles16
- Annexe B (normative) Détermination de l'incertitude18
- Annexe C (normative) Conception de meule artificielle20
- Bibliographie26
The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.
The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.
With Requirements, quickly access the main part of the normative text!
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ