NF EN ISO 3834-1

NF EN ISO 3834-1

April 2006
Standard Cancelled

Quality requirements for fusion welding of metallic materials - Part 1 : criteria for the selection of the appropriate level of quality requirements

ISO 3834-1:2005 provides criteria to be taken into account for the selection of the appropriate level of quality requirements for fusion welding of metallic materials, among the three levels specified in ISO 3834-2:2005 ISO 3834-3:2005 and ISO 3834-4:2005. It applies to manufacturing, both in workshops and at field installation sites.ISO 3834-1:2005 does not specify requirements for a total quality management system. However, quality management system elements where their inclusion will complement ISO 3834 are defined.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

April 2006

Number of pages

15 p.

Reference

NF EN ISO 3834-1

ICS Codes

25.160.01   Welding, brazing and soldering in general

Classification index

A89-250-1

Print number

1 - 06/04/2006

International kinship

ISO 3834-1:2005

European kinship

EN ISO 3834-1:2005
Sumary
Quality requirements for fusion welding of metallic materials - Part 1 : criteria for the selection of the appropriate level of quality requirements

ISO 3834-1:2005 provides criteria to be taken into account for the selection of the appropriate level of quality requirements for fusion welding of metallic materials, among the three levels specified in ISO 3834-2:2005 ISO 3834-3:2005 and ISO 3834-4:2005. It applies to manufacturing, both in workshops and at field installation sites.

ISO 3834-1:2005 does not specify requirements for a total quality management system. However, quality management system elements where their inclusion will complement ISO 3834 are defined.

Replaced standards (1)
NF EN 729-1
November 1994
Standard Cancelled
Quality requirements for welding. Fusion welding of metallic materials. Part 1 : guidelines for selection and use.

Le présent document fournit un moyen d'interprétation des exigences de la norme NF EN 29000 en ce qui concerne la partie d'un système qualité se rapportant à la maîtrise du soudage, considéré comme un "procédé spécial". Le présent document fait partie d'une norme en quatre parties: la partie 1 consiste en des lignes directrices pour la sélection et l'utilisation des exigences de qualité en soudage, la partie 2 définit les exigences de qualité complète, la partie 3 définit les exigences de qualité normale et la partie 4 définit les exigences de qualité élémentaire.

Standard replaced by (1)
NF EN ISO 3834-1
September 2021
Standard Current
Quality requirements for fusion welding of metallic materials - Part 1 : criteria for the selection of the appropriate level of quality requirements

This document specifies a general outline of the ISO 3834 series and criteria to be taken into account for the selection of the appropriate level of quality requirements for fusion welding of metallic materials, among the three levels specified in ISO 3834-2, ISO 3834-3 and ISO 3834-4. It is applicable to manufacturing, both in workshops and at field installation sites. This document does not specify requirements for a total quality management system (QMS). However, Clause 6 identifies QMS elements where their inclusion complements the ISO 3834 series.

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    1
  • 4 Aperçu général de l'ISO 3834
    2
  • 5 Sélection du niveau d'exigences de qualité
    3
  • 6 Éléments à prendre en compte dans un système de management de la qualité complétant l'ISO 3834
    4
  • Annexe A (informative) Critères d'aide au choix de la partie appropriée de l'ISO 3834
    5
  • Bibliographie
    7
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ