NF EN ISO 8503-2

NF EN ISO 8503-2

April 2012
Standard Current

Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2 : method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure

ISO 8503-2:2012 describes a visual and tactile method for assessing the grade of the profile which is produced by one of the abrasive blast-cleaning procedures described in ISO 8504‑2.The method uses ISO surface profile comparators for assessing, on site, the roughness of surfaces before the application of paint or other protective treatments.The method is applicable to steel surfaces which have been blast-cleaned by use of either shot abrasives or grit abrasives, but is only applicable to grades Sa 2½ and Sa 3 of ISO 8501‑1 where the entire surface under test shows an overall blast-cleaned appearance.lt is applicable to surfaces which have been cleaned with either metallic or non-metallic abrasives.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

April 2012

Number of pages

12 p.

Reference

NF EN ISO 8503-2

ICS Codes

17.040.20   Properties of surfaces
25.220.10   Surface preparation

Classification index

T35-503-2

Print number

1 - 10/04/2012

International kinship

ISO 8503-2:2012

European kinship

EN ISO 8503-2:2012
Sumary
Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2 : method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure

ISO 8503-2:2012 describes a visual and tactile method for assessing the grade of the profile which is produced by one of the abrasive blast-cleaning procedures described in ISO 8504‑2.

The method uses ISO surface profile comparators for assessing, on site, the roughness of surfaces before the application of paint or other protective treatments.

The method is applicable to steel surfaces which have been blast-cleaned by use of either shot abrasives or grit abrasives, but is only applicable to grades Sa 2½ and Sa 3 of ISO 8501‑1 where the entire surface under test shows an overall blast-cleaned appearance.

lt is applicable to surfaces which have been cleaned with either metallic or non-metallic abrasives.

Replaced standards (1)
NF EN ISO 8503-2
July 1995
Standard Cancelled
Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 2 : method for the grading of surface profile of abrasive blast-cleaned steel. Comparator procedure.

Table of contents
  • Avant-propos
    iv
  • Introduction
    v
  • 1 Domaine d'application
    1
  • 2 Références normatives
    1
  • 3 Termes et définitions
    2
  • 4 Principe
    2
  • 5 Appareillage
    2
  • 6 Entretien et réétalonnage des comparateurs viso-tactiles ISO
    2
  • 7 Mode opératoire
    2
  • 8 Rapport d'essai
    3
ZOOM ON ... the Requirements department
To comply with a standard, you need to quickly understand its issues in order to determine its impact on your activity.

The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.

The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.

With Requirements, quickly access the main part of the normative text!

With Requirements, quickly access the main part of the normative text!
New: UPSELL service
- The UPSELL service allows you to easily update one of your standards.
- With a single click, add a new language, the Requirements or Redline+ service and add one or more additional users.
- Whether you are in the process of acquiring a standard or it is already available in your personal space, the UPSELL service is available at every stage to help you understand it and implement it within your organization.
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ