IEC TS 60695-11-3:2004

April 2004

Technical specification Cancelled

Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods

Provides detailed requirements for the production of a 500 W nominal, pre-mixed type test flame. The approximate overall height is 125 mm.Two test flames are described: Method A may only be produced using methane whereas method C may be produced using either methane or propane.The main changes with respect to the previous edition are described below:- The introduction has been revised, - Test methods B and D have been withdrawn. Test methods A and C have been retained with their original letter designation, - Normative reference ISO 1337 has been withdrawn without a replacement by ISO/TC 26. The callout Cu-ETP UNS 11000 is the replacement for all references to ISO 1337. It is taken from ASTM B187-00 and describes high conductivity electrolytic copper, - A new Annex H has been added which provides access to equipment manufacturers and suppliers,- Alignment with other publications in the IEC 60695-11 series has been made, where appropriate. Has the status of a basic safety publication in accordance withIEC Guide 104.

Main informations

Collections

International IEC standards

Thematics

QSE, Gestion des risques et SST, Sécurité

Publication date

April 2004

Number of pages

63 p.

Reference

IEC TS 60695-11-3:2004

ICS Codes

13.220.40 Ignitability and burning behaviour of materials and products

29.020 Electrical engineering in general

Print number

1 - juin 2005

Sumary

Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods

Provides detailed requirements for the production of a 500 W nominal, pre-mixed type test flame. The approximate overall height is 125 mm. Two test flames are described: Method A may only be produced using methane whereas method C may be produced using either methane or propane. The main changes with respect to the previous edition are described below: - The introduction has been revised, - Test methods B and D have been withdrawn. Test methods A and C have been retained with their original letter designation, - Normative reference ISO 1337 has been withdrawn without a replacement by ISO/TC 26. The callout Cu-ETP UNS 11000 is the replacement for all references to ISO 1337. It is taken from ASTM B187-00 and describes high conductivity electrolytic copper, - A new Annex H has been added which provides access to equipment manufacturers and suppliers,- Alignment with other publications in the IEC 60695-11 series has been made, where appropriate. Has the status of a basic safety publication in accordance with IEC Guide 104.

Replaced standards (1)

IEC TS 60695-11-3:2000

March 2000

Technical specification Cancelled

Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods

Gives the detailed requirements for the production of a nominal 500 W, pre-mixed type test flame. the approximate overall height is 125 mm. Four methods are given: flame A and D may only be produced using methane, flame B may only be produced using propane and flame C may be produced using either methane or propane. Has the status of a basic safety publication in accordance with IEC Guide 104.

Standard replaced by (1)

IEC 60695-11-3:2012

August 2012

International standard Current

Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods

IEC 60695-11-3:2012 provides detailed requirements for the production of either of two 500 W nominal, pre-mixed type test flames. The approximate overall height of each flame is 125 mm. Two methods of producing a test flame are described: - Method A uses methane. - Method C can use either methane or propane. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. This first edition of IEC 60695-11-3 cancels and replaces the second edition of IEC/TS 60695-11-3 published in 2004. It constitutes a technical revision and now has the status of an International Standard. The main changes with respect to the second edition of IEC/TS 60695-11-3 are the integration of minor editorial and technical changes throughout the text. Keywords: Fire hazard, Test flames, 500 W flames

Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ