NF EN 1870-19

Le présent document détermine les prescriptions de sécurité des scies circulaires à table de menuisier (avec ou sans table mobile), des scies au format et des scies de chantier. Il s'applique également aux machines conçues pour le rainurage avec une largeur ne dépassant pas 200 mm. Il donne les moyens de se conformer aux Directives "Machines" 98/37/CE (voir Annexe ZA) et 2006/42/CE (voir Annexe ZB).

ISO 19085-10:2018 gives the safety requirements and measures for displaceable building site saws, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as "machines". NOTE 1 For the definition of displaceable machine, see ISO 19085‑1:2017, 3.5. ISO 19085-10:2018 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. The machine can also be fitted with a device for the saw blade to be manually raised and lowered through the table, whose hazards have been dealt with. This document does not apply to the following: a) machines with a maximum saw blade diameter smaller than 350 mm or greater than 500 mm; b) hand-held woodworking machines, including any adaptation permitting their use in a different mode, i.e. bench mounting; c) machines with a device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table; NOTE 3 Hand-held motor-operated electric tools are covered by IEC 62841‑1 together with IEC 62841‑2‑5. NOTE 4 Machines with the device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table are considered as table saws, covered by ISO 19085‑9. ISO 19085-10:2018 is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

This document gives the safety requirements and measures for stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as "table saws" (in the USA), hereinafter referred to as "machines", designed to cut wood and material with similar physical characteristics to wood. NOTE 1 For the definition of stationary and displaceable machine, see ISO 19085‑1:2017, 3.4 and 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. It is also applicable to machines fitted with one or more of the following devices, or working unit, whose hazards have been dealt with: — device for the main saw blade and scoring saw blade to be raised and lowered through the table; — device to tilt the main saw blade and scoring saw blade for angled cutting; — device for scoring; — device for grooving with milling tool with a width not exceeding 20 mm in one pass; — demountable power feed unit; — additional manually operated sliding table; — powered work-piece clamping device. NOTE 3 Circular saw benches are used for ripping, cross cutting, dimensioning and grooving. This document does not apply to: a) transportable/displaceable machines intended for outdoor use on building sites; NOTE 4 Building site saws (contractor saws) are covered by the requirements of ISO 19085‑10:2018. b) hand held woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting; c) machines intended for use in a potentially explosive atmosphere; d) machines manufactured before the date of its publication as an International Standard; e) transportable machines with a maximum saw blade diameter of ≤315 mm. NOTE 5 Transportable motor-operated electric tools are dealt with in IEC 62841‑1:2014 and IEC 62841‑3‑1:2014.